Download Print this page

KitchenAid KSSC36FT Specification Sheet

Side by side built-in refrigerator
Hide thumbs Also See for KSSC36FT:

Advertisement

PRODUCT MODEL NUMBERS
KSSC36FT
KSSO42FT
KSSC36QT
KSSO42QT
KSSC42FT
KSSO48FT
KSSC42QT
KSSO48QT
KSSC48FT
KSSP36QT
KSSC48QT
KSSP42QT
KSSO36FT
KSSP48QT
KSSO36QT
KSSS36FT
Electrical: A 115-volt, 60-Hz, AC-only 15- or
20-amp fused, grounded electrical supply is
required. It is recommended that a separate circuit
serving only your refrigerator be provided. Use an
outlet that cannot be turned off by a switch. Do not
use an extension cord.
Water Supply: A cold water supply with water
pressure of between 30 and 120 psi (207 and
827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your
water pressure, call a licensed, qualified plumber.
IMPORTANT: The pressure of the water supply
coming out of a reverse osmosis system going to
the water inlet valve of the refrigerator needs to be
between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60 psi (276 to 414 kPa).
The water shutoff should be located in the base
cabinet on either side of the refrigerator or some
other easily accessible area. The right-hand side is
recommended. The access hole through the cabinet
must be within 1/2" (12.7 mm) of the rear wall.
NOTE: If the water shut off valve is in the back
wall behind the refrigerator, it must be at an angle
so that the tube is not kinked when the refrigerator
is pushed into its final position.
If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the
floor or the back wall.
Do not install the refrigerator near an oven, radiator,
or other heat source, nor in a location where the
temperature will fall below 55°F (13°C).
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
®
Side by Side Built-In Refrigerator
PRODUCT DIMENSIONS
KSSS42FT
KSSS48FT
KSSS36QT
KSSS42QT
KSSS48QT
KSSC42QV
KSSC48QV
Model
36
42
48
³⁄₈
*83
"
(211.8 cm)
*When leveling legs are fully extended to
1 " (3.2 cm) below rollers, add 1 " (2.9 cm)
to the height dimensions.
TOP VIEW
A
25 "
(64.5 cm)
Width A
" (88.9 cm)
" (104.1 cm)
" (119.4 cm)
³⁄₈
25
"
(64.5 cm)
¹⁄₂
23
"
(59.7 cm)
SIDE VIEW
84" (213.4 cm)
Power Cord
¹⁄₂
*3
" (8.9 cm)
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
■ Height dimensions are shown with the
leveling legs extended to 1/8" (3 mm)
below the rollers.
■ The power cord is 84" (213 cm) long.
■ The water line attached to the back of
the refrigerator is 5' (1.5 m) long.
FRONT VIEW
A
(see chart following)
Model
Width A (Trim edge to trim edge)
36
36 " (92.1 cm)
42
42 " (107.3 cm)
48
48 " (122.6 cm)
³⁄₈
*83
"
(211.8 cm)
Page 1 of 2
Ref. 2316565C
09-09-08

Advertisement

loading

Summary of Contents for KitchenAid KSSC36FT

  • Page 1 IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa). If a reverse osmosis water filtration system is...
  • Page 2 The location must permit both doors to open to a minimum of 90°. Allow 4-1/2" (11.4 cm) minimum space between the side of the refrigerator and a corner wall. NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended handles on a Classic model.