Read these instructions completely and carefully. Product failure due to improper installation is not • IN PORTANT- Save these instructions covered under the GE Appliance Warranty. for local inspector's use. Observe all governing codes See the Owner's Manual for warranty information.
The water line should be 1/4" For a 90° door swing, allow 4" min. clearance to a wall, for framed and stainless steel models. Allow 5" min. O.D.copper tubing or GE SmartConnect kit between the cold water line and water connection location, clearance for professional series models.
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips Refrigerator to prevent interfeence with cabinet door 23-7/8" From swing. The opening must allow for filler strips. Rear of Refrigerator...
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, Refrigerator frameless cabinets mag require filler strips to Case Trim prevent interference with cabinet door swing. The opening must allow far filler strips. 23-7/8" FromRearof Refric_rator 1/4"...
Design Guide CUSTOMIZATION BASICS: Framed Or Overlag Panels, Custom Handles and Accessorg Kits Professional Style Stainless Steel Refrigerators Overlag panels Stainless steel wrapped refrigerators have beveled edges You mag also choose to install custom overlag panels and professional-style handles. These models are shipped from your cabinet manufacturer.
Design Guide 114" FRAMED PANEL DIMENSIONS Trim Reveal Door If gou choose to install framed panels, theg must be cut to the dimensions shown. The panels will slide into the frame on the door and grille. 1/4" Non-Dispenser Models Panel If the custom panel is less than 1/4"...
Design Guide 0veda 3/4" OVERLAY PANEL DIMENSIONS Door For a more custom appearance, overlag panels mag be installed on trimmed models. The averlag panel must be secured to a 1/4" thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the averlag and backer panel.
Design Guide DISPENSER MODELS: RAISED OVERLAY PANEL DESIGN 1/4" BackerPanel .lO"Spacer When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. • The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.
• 1/4", 5/16" Combo Rachet to have it replaced with a properlg grounded • 55" long 2x4 for Anti-Tip support 5-prong wall outlet. • 1/4" copper water line tubing or GE SmartConnect Refrigerator Tubing kits DO NOT, UNDER • Water shut-off valve ANY CIRCUMSTANCES, •...
• Avoid laging the unit on its back or side to prevent sealed sgstem restrictions. [STEP 3] INSTALL WATER LINE NOTE:The onlg GE approved plastic tubing is supplied in the GE SmartConnect Refrigerator Tubing kits. • A cold water supplg is required for automatic Do not use ang other plastic water supplg line because icemaker operation.
Installation Instructions [STEP 3] (continued) ISTEP 6 ] INSTALL ANTI-TIP BRACKETS WAR NIN G:ANT,-T,P PRECAUT,ONS Shut off the main water supplg. Turn on the nearest faucet long enough to clear the line The refrigerator is top-heavy and must be secured of water.
Installation Instructions [STEP 71 LEVEL REFRIGERATOR [STEP 81 ALTERNATE ANTI-TIP PROCEDURE All models have 4-point leveling. The front is supported b 9 leveling legs, the rear is supported The refrigerator must be secured to prevent tipping, b 9 adjustable wheels. Both are accessible from The anti-tip brackets cannot be used on metal the front of the refrigerator.
Installation Instructions ESTEP9] SECURE REFRIGERATOR ESTEP11] INSTALL GRILLE PANEL TO CABINETRY (for Custom Panel Models onlg) Whenever possible, perform this step for anti-tip To insert the framed or overlag panel into the grille: securitg, or when anti-tip brackets cannot be used. •...
Installation Instructions [STEP 12] INSTALL 114" FRAMED PANELS Go to Step 12A for Overlag Panels Handle Trim Refrigerator Door SuppliedHandle Shownin 1/4" PanelPosition Install door panels: • Open the door to 90 °. Remove the 6 Phillips head screws from the door handle. •...
Installation Instructions ISTEP 12AI INSTALL OVERLAY PANELS DoorTrim Haedle Trim Refrigerator Door Move Forward F0r3/4" Panel SuppliedHandle Shownin Overlay PanelPositioe Install door panels: • Open door to 90°. Remove the 6 Phillips head screws from the door handle. • Remove the handle. Retain all screws. •...
Page 17
Installation Instructions ISTEP 12AI (continued) ISTEP 12AI (continued) Custom Handles • Carefully place the aluminum cover trim into top • If gou are using custom handles, the handle must end cap so that the recess is aligned with the cap. be praperlg secured to the overlag panel before sliding...
See pages 7 and 8 for panel • Turn on the water to check for leaks. construction information. GE SmartConnect T"Tubing: • Insert the molded end of the tubing into the refrigerator connection. Tighten the compression nut until it isjust hand tight.
Installation Instructions [STEP 171 INSTALL TOEKICK [STEP 15] CONNECT POWER, CLOSE GRILLE PANEL • Locate the supplied toekick (shipped taped to the side of the refrigerator). Install with the 2 screws • Open the grill panel. provided, adjust to the desired height and tighten •...
ZKHSS2 Tubular Stainless Steel Handles This kit provides for the installation of Tubular Stainless Steel handles an 3/4" averlag custom panels. TOOLS AND MATERIALS REQUIRED [STEP 1] REMOVE DOOR HANDLES • Open the refrigerator door to 90 °. Remove In addition to the custom door panels, gou need: the 6 screws holding the handle to the door.
Page 21
ZKHSS2 Tubular Stainless Steel Handles [STEP 2 ] INSTALL HANDLE ONTO PANELS [STEP 2 ] (continued) Secure Handles to Panels Drill Pilot Holes • Measure, mark and draw a line, 1-1/8" from • Use a 7/8" spade bit to drill 1/2" to 9/16" max. depth into the back side of the panel.
ZKHSS2 Tubular Stainless Steel Handles [STEP 3] INSTALL ASSEMBLED HANDLES [STEP 4] INSTALL DISPENSER TRIM • Slide the assembled panels into the door trim. For Dispenser Models Onlg: • Secure both trims using all the original screws. There are two dispenser trims shipped with your dispenser refrigerator.
Page 24
For Honogrom ® local service in gour area, call 1.800,444.1845 NOTE: Product improvement is a continuing endeavor at General Electric Therefore, materials, appearance and specifications are subject to change without notice GE Consumer & Industrial Appliances General Electric Compang POOSJ...