Product failure due to improper installation • IMPORTANT- heseinstructions for is not covered under tile GE Appliance Warranty. See local inspector's liNe. Observe all governing codes tile Owner's Manual for warranty information. ordinances. WARNING: •...
The water line should be 1/4" O.D. copper robing or GE SmartConnect 4" minimum clearance is required when door swing between the cold water line and water connection is adjusted to 90 ° . If the 90 ° door stop position...
Design Guide FramelessCabinets:The case trim overlaps cabinets atthe top and sides. Therefore, frameless cabinets may require filler strips to )revent interfeence with cabinet Refrigerator door swing. The opening must allow for filler 23-7/8" From strips. Rearof Refrigerator " 2" Case 3/4"...
Design Guide FramelessCabinets: The case trim overlaps cabinets atthe top and sides. Therefore, Refrigerator frameless cabinets may require filler strips to _--Case _im prevent interference with cabinet door swing. The opening must allow for filler strips. 234/8" FromRearof Refrigerator ..1-1/4"...
Design Guide 1/4" FRAMED PANEL DIMENSIONS |_5/16" Trim Door Reveal If you choose to install flamed panels, they must be cut to the dimensions shown. The panels will slide into the flame on the (loot and grille..... 1/4" Non-Dispenser Models Panel If the custom panel is less than 1/4"...
Design Guide 3/4" OVERLAY PANEL DIMENSIONS Overlay Panel Door a more custom appearance, overlay panels installed on trimmed models. overlay panel must be secured to a 1/4" thick backer panel which slides into uim. A spacer panel 0.10" thick must Backer P anel placed between...
Design Guide DISPENSER MODELS: RAISED OVERLAY PANEL DESIGN 1/4"Backer Panel .10"Spacer When a raised panel design is to be used, a 3/4" Overlay custom wide middle rail is required to accept the dispenser trim. • The middle rail must be wide enough to allow for the dispenser uim to overlap the opening.
DO NOT USE AN EXTENSION CORD WITH THIS MATERIALS REQUIRED APPI fiANCE. • 35" long 2x4 for Anti-Tip support • 1/4" copper water line robing or GE SmartConnect Refligerator Tubing kits • Water shut-off vane (optional but recommended) • Custom panels for doors and grille panel •...
////// accommodate bend leading into tile water lille COIlllectioIl. Packin_ NOTE: Tile only GE approved plastic robing is supplied ill tile GE SmartConnect Refligerator Tubing kits. Do not use any other plastic water supply Outlet Valve lille because tile lille is under pressure at all times.
Installation Instructions STEP 4 INSTALL ANTI-TIP BRACKETS STEP 2 (continued) WARNING:ANT,-T,P PRECAUT,ONS • Turn on the main water supply and flush debris. Run about a quart of water through the robing into The refiigerator is top-heax T and must be secured a bucket.
Installation Instructions STEP 6 SECURE REFRIGERATOR STEP 5 LEVEL REFRIGERATOR TO CABINETRY All models have 4-point leveling. fiont X4rhenever possible, perform this step for anti-tip supported by leveling legs, rear is supported securiD_, or when anti-tip brackets cannot be used. adjustable wheels.
Installation Instructions STEP 8 INSTALL GRILLE PANEL To insert fiamed or overlay panel into the grille: • Raise the grille panel to stop position. Id" Lotqosen Loosen Side Side Trim Trim Screw Screw AdjustNut Below Springto Accommodate Panel W eight •...
Installation Instructions STEP 9 INSTALL FRAMED PANELS Goto Step 9Afor OverlayPanels Handle DoorTrim Trim-_ Refrigerator Door I_\\\\\\\\\\\\\\\\\\\\\1 Supplied Handle Shown in 1/4" Panel Position Install door panels: • Open door to 90 °. Remove the 6 Phillips head screws flom the door handle. •...
Installation Instructions [STEP 9A INSTALL OVERLAY PANELS DoorTrim Handle Trim _" • Refrigerator Door Move Forward For3/4" {_0t Panel .iiii Supplied Handle Shown in Overlay Panel Position Install door panels: • Open door to 90 °. Remove the 6 Phillips head screws flom the door handle.
Insert robe into the construction information. union fitting on the unit and tighten nut to union. • Turn on the water to check for leaks. GE SmartConnect Tubing: • Insert the molded end of the robing into the refligerator connection.
Installation Instructions STEP 14 INSTALL TOEKICK [STEP 12 CONNECT POWER • I,ocate tile supplied toekick (shipped roped to • Check to be sure the power cord is plugged into tile side of tile refligerator). Install with 2 screws tile receptacle. provided, adjust to desired height and tighten scIews.