GE ZISS480DXBSS Installation Instructions Manual
GE ZISS480DXBSS Installation Instructions Manual

GE ZISS480DXBSS Installation Instructions Manual

Side by side refrigerators
Hide thumbs Also See for ZISS480DXBSS:

Advertisement

Installation
Instructions
Side by Side Refrigerators
Design Guide
With Installation Instructions
31-46514-1
4
224D1889P01
01-13 GE
monogram,corn

Advertisement

Table of Contents
loading

Summary of Contents for GE ZISS480DXBSS

  • Page 1: Step 2, Install Handles Onto Panels

    Installation Instructions Side by Side Refrigerators Design Guide With Installation Instructions 31-46514-1 224D1889P01 01-13 GE monogram,corn...
  • Page 2: Table Of Contents

    , IMPORTANT- Save these instructions Product failure due to improper installation is not covered under the GE Appliance Warranty. local inspector's use. Observe all governing codes and See the Owner's Manual for warranty information. ordinances.
  • Page 3: The Installation Space

    1/4" For a 90 ° door swing, allow 4" min. clearance to a wall, for framed and stainless steel models. Allow 5" min. O.D. copper tubing or GE SmartConnect kit between the cold water line and water connection...
  • Page 4: 130 ° Door Swing

    Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips Refrigerator to prevent interfeence with cabinet door 23-7/8" From swing. The opening must allow for filler strips. Rearof Refrigerator Case Trim 3/4"...
  • Page 5: 90 ° Door Swing

    Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top Gnd sides. Therefore, Refrigerator frameless cabinets may require filler strips to _Case prevent interference with cabinet door swing. The opening must GIIow for filler strips. 23-7/8" From Rearof Refrkerator ,.---, ..
  • Page 6: Customization Basics

    Design Guide CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Professional Style Stainless Steel Refrigerators Overlay panels Stainless steel wrapped refrigerators have beveled edges You may also choose to install custom overlay panels from and professional-style handles. These models are shipped your cabinet manufacturer.
  • Page 7: 1/4" Framed Panel Dimensions

    Design Guide 1/4" FRAMED PANEL DIMENSIONS "'!75!!6" Door If you choose to install framed panels, they must Reveal be cut to the dimensions shown. The panels will slide into the frame on the door and grille, ....1!4" Non-Dispenser Models Panel If the custom panel is less than 1/4"...
  • Page 8: 3/4" Overlay Panel Dimensions

    Design Guide 3/4" OVERLAY PANEL DIMENSIONS OverlaL Door For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4" thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed £ackerPanel between the overlay and backer panel.
  • Page 9: Raised Overlay Panel Design

    Design Guide DISPENSER MODELS: RAISED OVERLAY PANEL DESIGN 1!4" Backer Pan_4 .10" Spacer When a raised panel design is to be used, 3/4" Overlay Par_ a custom wide middle rail is required to accept the dispenser trim. , The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.
  • Page 10: Side Panels

    ,35" long 2x4 for Anti-Tip support 3-prong wall outlet. , !/4" copper water line tubing or GE SmartConnect TM Refrigerator Tubing kits DO NOT, UNDER , Water shut-off valve ANY CIRCUMSTANCES,...
  • Page 11: Step 1, Remove Packaging

    Other types be between 40 and 120 p.s.i. of plastic may crack or rupture with age and cause , Route 1/4" OD copper or GE SmartConnect water damage to your home. plastic tubing between house cold water...
  • Page 12: Step 6, Install Anti-Tip Brackets

    Installation Instructions ISTEP 6 1 INSTALLANTI-TIPBRACKETS [STEP 3] (continued) WARNING: ANTI-TIP PRECAUTIONS Shut off the main water supply. Turn on the nearest faucet long enough to clear the line The refrigerator is top-heavy and must be secured of water. to prevent the possibility of tipping forward. , Install a shut-off valve between the icemaker...
  • Page 13: Step 7, Level Refrigerator

    Installation Instructions ISTEP 71LEVEL REFRIGERATOR ISTEP 8 ALTERNATE ANTI-TIP PROCEDURE All models have 4-point leveling. The front is supported by leveling legs, the rear is supported The refrigerator must be secured to prevent tipping. by adjustable wheels. Both are accessible from The anti-tip brackets cannot...
  • Page 14: Step 9, Secure Refrigerator To Cabinetry

    Installation Instructions [STEP 9] SECURE REFRIGERATOR ISTEP 111 INSTALL GRILLE PANEL TO CABINETRY (for Custom Panel Models only) Whenever possible, perform this step for anti-tip To insert the framed or overlay panel into the grille: security, or when anti-tip brackets cannot be used.
  • Page 15: Step 12, Install Framed Panels

    Installation Instructions [STEP 121 INSTALL 1/4" FRAMED PANELS Step 12AforOverlay Panels Handle Door Trim Trim !]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_!]_i!_ !]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]i! Refrigerator !]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]i! Door !]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]!]i! _l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_lil_l_l I_\\\\ \\\\\\\\\\\\\\\\\'1 Suppfied H_Jndle Shown in 7/4" P_ne/ Position Install door panels: . Open the door to 90 °. Remove the 6 Phillips head screws from the door handle, .
  • Page 16: Step 12A, Install Overlay Panels

    Installation Instructions ISTEP 12A I INSTALL OVERLAY PANELS Door Trim Handle Trim Refrigerator Door Move Forward For 3/4" k\\\\\\\\\\\\\\\\\\\\\l Panel Supplied Handle Shown in Overlay Pane/Position Install door panels: . Open door to 90 °. Remove the 6 Phillips head screws from the door handle, .
  • Page 17 Installation Instructions ISTEP12AI (continued) ISTEP 12A1 (continued) Custom Handles , Carefully place the aluminum cover trim into top , If you are using custom handles, the handle must end cap so that the recess is aligned with the cap. be properly secured to the overlay panel before sliding Use the top to bottom grooves...
  • Page 18: Step 13, Install Dispenser Trim

    , Turn on the water to check for leaks. GE SmartConnect _ Tubing: , Insert the molded end of the tubing into the refrigerator connection. Tighten the compression nut until it isjust hand tight.
  • Page 19: Step 16, Start Icemaker

    Installation Instructions ISTEP 171 INSTALL TOEKICKS ISTEP 151CONNECT POWER, CLOSE GRILLE PANEL . Locate the supplied toekicks (shipped taped to the side of the refrigerator). . Open the grill panel. . First, attach the LARGER toekick to the refigerator . Plug in the power cord (if necessary) by reaching using ONLY the top center hole (1).
  • Page 20: Step 1, Remove Door Handles

    ZKHSS2 Tubular Stainless Steel Handles This kit provides for the installation of Tubular Stainless Steel handles on 3/4" overlay custom panels. TOOLS AND MATERIALS REQUIRED [STEP 1[ REMOVE DOOR HANDLES , Open the refrigerator door to 90 °. Remove In addition to the custom door panels, you need: the 6 screws holding the handle to the door.
  • Page 21 ZKHSS2 Tubular Stainless Steel Handles [STEP2 INSTALLHANDLE ONTO PANELS [STEP 2 ](continued) Drill Pilot Holes Secure Handles to Panels , Heasure, mark and draw a line, !-!/8" from , Use a 7/8" spade bit to drill !/2" to 9/!6" max. depth the handle side edge, top to bottom.
  • Page 22: Step 3, Install Assembled Handles

    ZKHSS2 Tubular Stainless Steel Handles [STEP3 INSTALL ASSEMBLEDHANDLES [STEP 41 INSTALL DISPENSER TRIM . Slide the assembled panels into the door trim. For Dispenser Models Only: , Secure both trims using all the original screws. There are two dispenser trims shipped with your dispenser refrigerator.
  • Page 23 Notes...
  • Page 24 _ local service in your area, call 1.800.444.1845. NOTE:Product improvement is o continuing endeavor (st General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Appliances & Lighting 2122-465-14-1 Appliances 4D1889P014 I General Electric Company Louisville, KY40225 01-13 GE GEAppliances.com...

Table of Contents