Payne PA1P048 Installation & Start-Up Instructions page 9

UNiT SIZE
NOMINAL CAPACITY (ton)
OPERATING WEIGHT (lb.)
COMPRESSOR
REFRIGERANT (R=22)
Quantity (lb.)
REFRIGERANT METERING DEVICE
Orifice ID {in.)
CONDENSER COIL
Rows...Fins/in.
Face Area (sq, ft.)
CONDENSER FAN
NominN Cfm
Diameter
Motor Np (Rpm)
EVAPORATOR COiL
Rows...Fins/in.
Face Area (sq, ft,)
EVAPORATOR BLOWER
Nominal Airflow (Cfm)
Size (in.)
Motor Hp (RPN)
RETURN-AIR FILTERS (in.)*
Throwaway
Required filter sizes shown are based on the larc
Table 1--Physical Data--Unit PAl P
018 024 042 048 0$0
1-1/2 2 3-1/2 4 5
254 260 294 324 389
Scroll Reciprocating
2.6 3.5 6.4 5.1 7.4
.034 .034 .034 .032 .030
1...17 1...17 1...17 1...17 2...17
6.1 9.1 9.1 12.3 12.3
2000 2400 3000 3600 3600
22 22 22 22 22
1/8 (825) 1/8 (825) 1/4 (I100) 1/4 (I100) 1/4 (1100)
2._15 2...15 4...15 3._15 4._15
3.1 3.1 3.06 4.7 4.7
600 800 1400 1600 2000
10x10 10x10 11x10 11x10 11x10
1/4 (825) 1/4 (1075) 3/4 (I075) 3/4 (I075) 1.0 (1100)
20x20 20x20 20x24 24x30 24x30
er of the ARI (Air Conditioning and Refrigeration Institute) rated cooling airflow or the heating airflow velocity of 300 ft./min
for throwaway type or 450 ft/min for high-capacity type Air filter pressure drop for non-standard filters must not exceed 008 in. wg.
030 036
2-1/2 3
258 268
Reciprocating
3.65 4.4
Accurater
.034 .032
1._17 1._17
9.1 10.9
2400 3000
22 18
1/8 (825) 1/4 (I100)
2...15 3...15
3.7 3.06
1000 1200
10x10 11x10
1/4 (1075) 1/2 (1075)
20x20 20x24
UNIT SIZE
NOMINAL CAPACITY (ton)
OPERATING WEIGHT (lb.)
COMPRESSOR
REFRIGERANT (R°22)
Quantity (lb.)
REFRIGERANT METERING DEWCB
Orifice ID (in.)
CONDENSER COIL
Rows...Finsiin.
Face Area (sq. ft.)
CONDENSER FAN
Nominal Cfm
Diameter (in.)
Motor Np (Rpm)
EVAPORATOR COIL
Rows...Finslin.
Face Area (sq. ft.)
EVAPORATOR BLOWER
Nominal Airflow (Cfm)
Size (in.)
Motor Np (RPM)
RETURN-AIR FILTERS (in.)*
Throwaway
Table 2--Physical Data--Unit PA2P
024 636 636 042 048 666
2 2-1/2 3 3-1/2 4 5
270 291 299 321 326 399
Scroll
3.7 4.4 5.2 7.6 8.3 8.1
Accurater
.034 .030 .032 .034 .034 .032
1._17 1...17 2._17 2...17 2...17 2._17
10.8 12.7 9.1 9.1 12.3 16.4
2350 2350 2350 3300 3300 3300
22 22 22 22 22 22
1/8 (825) 1/8 (825) 1/8 (825) 1/4 (1100) 1/4 (I100) 1/4 (1100)
3...15 3._15 3._15 3...15 4._15 4._15
3.1 3.1 3.7 4.7 4.7 4.7
800 1000 1200 1400 1600
1750
10x10 10x10 1lx10 1lx10 11x10
11x10
1/4 1/4 1/2 3/4 3/4
1.0 (1040)
1/4 (1075) 1/4 (1075) 1/2 (1075) 3/4 (1075) 3/4 (1075)
20x20 20x20 20x24 20x30 24x30 24x30
Required filter sizes shown are based on the larger of the ARI (Air Conditioning and Refrigeration Institute) rated cooling airflow or the heating airflow velocity of 300 ft./min
for throwaway type or 450 ft/min for high-capacity type Air filter pressure drop for non-standard filters must not exceed 008 in. wg.
1" (25mm) MIN.
TRAP
OBTLET *,
2" (50ram) MIN.
Fig. 7--Condensate Trap
C99013
12 Size all ductwork %r maximum required airflow (either heating or cooling) %r unit being installed, Avoid abropt duct size increases or
decreases or performance may be affected
9