Payne PA1P048 Installation & Start-Up Instructions page 22

Table 9--Wet Coit Air Delivery (Deduct 10 percent for 208v)*
Horizontal and Downflow Discharge
Unit PA2P024o060
230 AND 460 VOLT
Motor External Static Pressure (in. wg)
Unit
Speed 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Watts 281 282 281 278 276
Low
Cfm 833 776 702 638 554
Watts 375 370 363 357 352
024 Med
Cfm 894 800 754 636 518
Watts 468 457 444 431 423
High Cfm 884 802 697 467 397
Watts 246 244 243 241
Low
Cfm 910 806 749 680
Watts 343 339 336 332 328 322 317
030 Med
Cfm 1148 1104 1028 958 850 782 645
Watts 441 432 421 410 400
High Cfm 1102 988 896 783 529
Watts 470 458 445 430 415 399 384
Low
Cfm 1352 1257 1240 1199 1107 1015 924
Watts 514 501 487 471 455 438 422
03G Med
Cfm 1338 1295 1288 1181 1111 968 813
Watts 646 636 626 614 602 589
High Cfm 1385 1268 1196 1159 1032 948
Watts 625 614 605 593 574 549 518 485 454
Low
Cfm 1540 1510 1473 1396 1348 1288 1192 1124 1037
Watts 726 695 661 625 591 561 540
042 Med
Cfm 1648 1593 1530 1446 1352 1237 1114
Watts 790 766 7421 713
High Cfm 1616 1492 1394 1283
Watts 588 577 572 566 556 539 517 491
Low
Cfm 1514 1543 1467 1408 1374 1324 1237 1161
Watts 756 738 719 699 676 650 623 596 572 555
048 Med
Cfm 1785 1765 1706 1628 1577 1503 1421 1357 1298 1253
Watts 896 862 829 800 775 752 728
High Cfm 1880 1804 1704 1547 1565 1406 1367
Watts 903 898 873 842 814 792 777 764 743 701 618
Low
Cfm 2190 2158 2081 2026 1958 1866 1822 1744 1678 1535 1377
Watts 1002 978 960 941 914 880 839 798 764 750
060 Med
Cfm 2389 2291 2216 2120 2020 1952 1852 1727 1617 1549
Watts 1080 1080 1066 1041 1008 972 938
High Cfm 2316 2181 2122 2101 2000 1802 1672
Air delivery values are based on operating voltage of 230v or 460v, wet coil, without filter or electric heater. Deduct filter and electric heater pressure drops to obtain static
pressure available for ducting.
NOTES:
1 Do not operate the unit at a cooling airflow that is less than 350 cfm for each 12,000 Btuh of rated cooling capacity Evaporator ceil frosting may occur at airflows below
this point.
2 Dashes indicate portions of table that are beyond the blower motor capacity or are not recommended.
O. EVAPORATOR BLOWER AND MOTOR
NOTE: All motors are prelubricate& Do not attempt to lubricate these motors
For longer lit'c, operating economy, and continuing efficiency, clean accumulated dirt and grease from the blower wheel and motor annually.
Z_ WARNmNG: Disconnect and tag electrical power to the unit before cleaning the blower motor and wheel Faiture to
adhere to this warning coumd cause personal injury or death.
To clean the blower motor and wheel:
1. Remove and disassemble blower assembly as %llows:
a Remove unit access panel
b. Disconnect motor lead t?om time delay relay (TDR). Disconnect yellow lead t?om terminal L2 of the contactor.
c. On all units remove blower assembly t'rom unit. Remove screws securing blower to blower partition and slide assembly out. Be carefid
not to tear insulation in blower compartment.
d. Ensure proper reassembly by marking blower wheel and motor in relation to blower housing befbre disassembly.
e. Loosen setscrew(s) that secures wheel to motor shaR, remove screws that secure motor mount brackets to housing, and slide motor and
motor mount out of housing.
22