Frigidaire FAH14EQ2T3 Installation Instructions Manual

Installation Instructions
Do This First
(for existing sleeve)
Note that the air conditioner dimensions are: 24" wide,
14Y_"high, and 22" deep (without front). Install Air
Conditioner according to these installation instructions
to achieve the best performance. Save these installation
instructions for future reference.
Items in Kit
You may not need att parts in the kit. Discard unused
parts.
Tapered Spacer Blocks
Centering/Support Blocks
Plastic Divider
Stuffer Seat
Seal
Seal
Seal
Seal
Seal
Trim Frame (side legs)
Trim Frame (top & bottom legs)
Ground Wire (green)
Nut for grounding screw
Grounding Screw
Grille (plastic)
Grille Aluminum
Nuts (plastic)
Screw w/washer
How to Install
17" Long
4Y,"x 3Y,"x I'A ''
1/8" x 4Y_"x 14_A ''
1 "x lY_"x 84"
11/_"x lY_"x 25"
lY_"x lY_"x 14"
1½"x 3/8"x 25"
11A"x 3/8"x 14"
1" x 3/4"x 14"
1. Identify the wall-sleeve brand for your installation,
from the chart below.
Brand
White-Westinghouse
Frigidaire
Carrier (52F Series)
General Electric/
Hotpoint
Whirlpool
Qty.
2
2
1
1
2
2
2
2
1
2
2
1
1
1
1
1
4
4
Wall Sleeve Dimensions
(inches)
Width Height Depth
}25Y_ 15_A 17'/_
16,
or 22
26 15%
25% 16'/.
16:A
17,A
or 23
16Y4
or 19_/.
18%
15
18%
163/,
Fedders/Emerson 27 163/4
Sears/Kenmore 25% 167A
Emerson/Fedders 263A 15%
Carrier (51S Series) 253A 16½
Friedrich 27 16%
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition and
have a rear grille that securely attaches to sleeve, or
rear flange that serves as a stop for the Air Conditioner.
CAUTION: When installation is complete, replacement
unit MUST have a rearward
slope as shown.
Wail
Sleeve
REAR i
2. Remove old Air Conditioner from wall sleeve and
prepare wall sleeve as follows:
-- Clean interior (do not disturb seals).
-- Wall sleeve must be securely fastened in wall before
installing Air Conditioner. Drive more nails or screws
through sleeve, into wall, if needed.
-- Repair paint if needed.
3. If not existing, drill a 3/16"clearance hole for ground-
ing screw through left side of wall sleeve, in a clear area
about 3 inches maximum (to suit) back from front edge
of sleeve as shown below. Next attach ground wire inside
sleeve, using grounding screw, nut washer pull loose
end of ground wire out front of sleeve, and temporarily
bend it down and around lower edge of sleeve.
Waseev j 3 1
sleeve grounding Max I_- Hole
4. Prepare the wall sleeve for installation of the new unit
per the following Brand instructions.
#1 Emerson 15" Deep
#2 Fedders 19_" Deep
#3 Fedders or Friedrich 16_" Deep
#4 General Etectric/Hotpoint 16_" Deep
#5 Sears or Carrier (51S Series) 18%" Deep
#6 Whirlpool 17'A" Deep
#7 Whirlpool 23" Deep
#8 White-Westinghouse/Frigidaire/ 16"+ 17'/_"Deep
Carrier (52F Series)
#9 White-Westinghouse/Frigidaire 22" Deep
5. Install new unit into wall sleeve.
6. To attach ground wire to the new unit, remove the
screw from the left side front.
7. Assemble and install the
Trim Frame (see instruction).
P/N 220218A029