Advertisement
Available languages
Available languages
Installation
Instructions
Minimum
Clearance
Other Than Alcove or Closet Installation
Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and rear. Consideration
must be given to provide adequate clearance for installation and service.
I-_ PREPARING FOR INSTALLATION
OF NEW APPLIANCE
DISCONNECTING
GAS
_,
TURN G AS
SHUT-OFF
VALVE
IC_-_
DISCONNECT
AND DISCARD
OLD
_m]_-//_z_,,_,
TO THE OFF
_
FLEXIBLE
GAS CONNECTOR
AND
PosmoN.
OLDTRANSmONDUCT,NG
MATERIAL.
REPLACE
WITH NEW
CSA(AGA)
APPROVED
FLEXIBLE
GAS LINE CONNECTOR
AND UL
APPROVED
TRANSITION
DUCT.
WARNING - NEVER REUSE OLD
FLEXIBLE CONN ECTORS.
The use of old flexible connectors can cause leaks
and personal injury. Always use new flexible connec-
tors when installing gas appliances.
REMOVING LINT FROM WALL
EXHAUST OPENING
• Remove and discard existing plastic or metal foil
transition duct and replace with UL listed transition duct.
_j
WALL
INTERNAL
__,_,.DUCT
_
CHECK THAT EXHAUST
0PENING _..._,
\ q
, ,,
HOOD DAMPER O PENS
AND CLOSES FREE L Y,
TILTTHE APPLIANCE
SIDEWAYS AND REMOVE
THE FOAMSHIPPING PADS
BY PULLINGATTHE SIDES
AND BREAKINGTHEM
AWAY FROMTHE APPLIANCE
LEGS.BESURETO REMOVE
ALL OFTHE FOAM PIECES
AROUND THE LEGS.
After the machine is in the home,
remove remaining packing material/
carton from washer.
DO NOT REMOVE SHIPPING ROD AT
THIS TIME.
Removestyrofoam block.
Removethe bag containing the
Washer hoses and parts parts from
tub. Put styrofoam block back in tub
II
SturofoamBlock
L
opening to hold tub in place during the
rest of installation.
Move washer close to final
position. Make sure there is at least
a 24" clearance on right side of
washer to remove shipping bar. PULL
SHIPPING BAROUT USINGYELLOW
PLASTIC HANDLE.Keep bar so it can
[
Plastic
/
Handle
be reinstalled if washer is ever moved
again.
NEW HOME OR REMODELING FAUCETS/
DRAIN STANDPIPE/ELECTRICAL LOCATION
12"-_
...................
Locate spigots,
drain standpipe
and electrical plug
in this area
I
Right side of
Laundry Center
T
-i
42"
33"!
J
FLOOR
[] GAS REQUIREMENTS
- WARNING
• Installation
must conform to local codes end
ordinances, o r intheir absence, the NATIONAL
FUEL GAS CODE, ANSI Z223.
•Thisgasdrgerisequippedwithe Valve& Burner
Assembly foruseonlgwithnatural gas.Using
conversion kit WE2SM73 for24"Modelsor
WE2SM74 for27"Models,your local service
organization can convertthis dryerforusewith
propane iLP) g as.ALL CONVERSIONS MUST BE
MADE BY PROPERLV TRAINED AND QUALIFIED
PERSONNEL AND IN ACCORDANCE WITH LOCAL
CODES AND ORDINANCE REQUIREMENTS.
• Theappliance
mustbedisconnected
fromthe gassupply
piping system during anypressure testing
ofthat s ystem
ata test p ressure in excess o f0.5 PSI 13.4 K Pa}.
• Theappliance mustbeisolated fromthegassupply
piping systemby closing theequipment shut-offvalve
during any pressure testing ofthegassupply piping
oftest pressure equal toorless t han0.5 PSI 13.4 K Pa}.
27"GASSUPPLVCONNECTION
Note: 24" Gos supplg connection
has a flexible
hose thus dimensions will vary.
4
Advertisement
