Alpine INA-W910R Owner's Manual page 34

Adjusting Bass/Treble
You can change the bass or treble frequency emphasis
to create your own tonal preference.
Touch [ ] of Bass/Treble to adjust screen.
• Adjustment cannot be performed when Defeat is set to ON.
Setting the Bass level
You can emphasise or weaken the bass frequency.
Touch [ ] or [ ] of Bass Level to select the desired bass level.
Setting range: –6 to +6
• When G-EQ is set in "Setting EQ mode" (page 35), the level value
may change correspondingly with the value set in Band 1.
• When P-EQ is set in "Setting EQ mode" (page 35), the level value
may change correspondingly with the value set in Band 1.
Setting the treble level
You can emphasise or weaken the treble frequency.
Touch [ ] or [ ] of Treble Level to select the desired treble
level.
Setting range: –6 to +6
• When G-EQ is set in "Setting EQ mode" (page 35), the level value
may change correspondingly with the value set in Band 7.
• When P-EQ is set in "Setting EQ mode" (page 35), the level value
may change correspondingly with the value set in Band 5.
Setting the Bass Centre Frequency
The displayed bass frequency is emphasized.
Touch [ ] or [ ] of Bass Freq. to select the desired bass centre
frequency.
Setting range: 63 Hz
• The operation can be performed only when the P-EG is selected in
"Setting EQ mode" on page 35.
• When P-EQ is set in "Setting EQ mode" (page 35), the bandwidth
value may change correspondingly with the value set in Band 1.
Setting the Bass Bandwidth
Changes the boosted bass bandwidth to wide or narrow.
A wider setting will boost a wide range of frequencies
above and below the centre frequency. A narrower
setting will boost only frequencies near the centre
frequency.
Touch [ ] or [ ] of Bass Bandwidth to select the desired bass
bandwidth.
Setting range: Wide (Narrow) 1 to Wide 4 (Wide)
• The operation can be performed only when the P-EG is selected in
"Setting EQ mode" on page 35.
• When P-EQ is set in "Setting EQ mode" (page 35), the bandwidth
value may change correspondingly with the value set in Band 1.
Setting the Treble Centre Frequency
The displayed treble frequency is emphasized.
Touch [ ] or [ ] of Treble Freq. to select the desired Treble
centre frequency.
Setting range: 10 kHz
• The operation can be performed only when the P-EG is selected in
"Setting EQ mode" on page 35.
• When P-EQ is set in "Setting EQ mode" (page 35), the frequency
value may change correspondingly with the value set in Band 5.
Subwoofer On and Off
Touch [ ] or [ ] of Subwoofer to set to ON or OFF.
OFF: Subwoofer output is off.
ON: Subwoofer output is on.
34
-EN
80 Hz 100 Hz 200 Hz
12.5 kHz 16 kHz 17.5 kHz
Adjusting the Subwoofer Level
When ON is set in "Subwoofer On and Off ", the item is
displayed.
When an External Audio Processor is connected, the list is not
displayed.
1 Touch [ ] of Subwoofer.
The display change to the Subwoofer Adjusting screen.
2 Touch [ ] or [ ] of Level to adjust the subwoofer output.
Setting range: 0 to 15
Switching the Subwoofer phase
When ON is set in "Subwoofer On and Off" while the car is
parked, the item is displayed.
The subwoofer output phase is toggled subwoofer normal (0°) or
subwoofer reverse (180°).
1 Touch [ ] of Subwoofer.
The display change to the Subwoofer Adjusting screen.
2 Touch [ ] or [ ] of Phase to select to 0° or 180°.
• When the IMPRINT audio processor is connected, set "Changing
MultEQ mode" (page 50) to OFF while the car is parked.
Setting the Subwoofer System
When ON is set in "Subwoofer On and Off" while the car is
parked, the item is displayed.
1 Touch [ ] of Subwoofer.
The display change to the Subwoofer Adjusting screen.
2 Touch [ ] or [ ] of System to select to System 1 or System 2.
System 1: Subwoofer level changes according to the main
volume setting.
System 2: Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
Setting the Subwoofer Channel
When ON is set in "Subwoofer On and Off" while the car is
parked, the item is displayed.
1 Touch [ ] of Subwoofer.
The display change to the Subwoofer Adjusting screen.
2 Touch [ ] or [ ] of Channel to select to Stereo or Mono
(monaural).
Stereo: Subwoofer stereo (L/R) output
Mono: Subwoofer monaural output
• When the IMPRINT audio processor is connected, set "Changing
MultEQ mode" (page 50) to OFF while the car is parked.
Adjusting the Subwoofer Level
When an external audio processor is connected, the list is
displayed.
Touch [ ] or [ ] of Subw. Level to adjust the subwoofer output.
Setting range: 0 to 15