Related Manuals for Interlogix TruVision TVC-6110-1-N
Summary of Contents for Interlogix TruVision TVC-6110-1-N
- Page 1 TruVision TVC-6110-1 / TVC-6120-1 Camera User Manual P/N 1072543B-EN • ISS 21JUN12...
- Page 2 Copyright © 2012 UTC Fire & Security. All rights reserved. Trademarks and The TruVision and Interlogix names and logo are trademarks of patents UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
-
Page 3: Table Of Contents
Content Product overview 2 Package Contents 2 Features 2 User guidelines 2 Product description 3 Installation 4 Attach the lens 4 Connect the cables 4 Programming 6 OSD control button 6 Access the Setup menu 6 Save changes 7 Select the lens type 7 Set shutter/AGC 8 Set white balance 9 Set backlight compensation (BLC) 10... -
Page 4: Product Overview
Product overview The TVC-6110-1-N(-P)/ TVC-6120-1-N(-P) camera uses a digital signal processor (DSP) to process video signals. The camera includes a microcontroller to provide high-quality images with high-color reproduction and sharp pictures. Package Contents The package contains the following: • Box camera •... -
Page 5: Product Description
WARNING: To reduce the risk of fire or electronic shock, do not expose the camera to rain or moisture and do not remove the cover or back. Product description Figure 1: Product description - TVC-6110-1-N(-P) 1. OSD control button 4. Video output 2. -
Page 6: Installation
Installation Please check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. To install the camera you will need to prepare the mounting surface, mount the camera, attach the lens, and make cable connections. - Page 7 Power supply Monitor Note: TVC-6110-1-N(-P) is 12 VDC only. TruVision TVC-6110-1 / TVC-6120-1 Camera User Manual...
-
Page 8: Programming
Programming Once the camera hardware has been installed, the camera can then be configured. Program the camera by attaching a standard video monitor to the system. To connect the monitor: 1. Plug the monitor output cable to the video monitor output connector. 2. -
Page 9: Save Changes
Table 2: Setup menu description Menu item Description Lens Defines autoiris or manual iris. Shutter/AGC Define the method of iris control, shutter and AGC. White Bal Defines the white balance (WB) set up. Backlight Defines the highlight compensation (HLC) and backlight compensation (BLC) set up. -
Page 10: Set Shutter/Agc
Manual menu: Select a higher shutter speed value to see movement and a lower value to see clearer images. The shutter speed available are 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000 and 1/10000. The AGC value can be set between 6 and 44.8. -
Page 11: Set White Balance
Low luminance: Sets the lux level for low light conditions. Mode: Only AGC is available. Brightness: Adjust the brightness to X0.25, X0.50, X0.75 or X1. Manual shutter menu: Mode: Only Shut/AGC available. Shutter: Set the manual shutter to 1/60(1/50), 1/100(1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000 or 1/10000. -
Page 12: Set Backlight Compensation (Blc)
Menu Item Description has no limits between 1,800 to 10,500˚K so it may over-compensate the WB for a large single-color object. User1 This is a fixed white balance that is user-defined by blue and red gain parameters. Only use this function when there is steady light. Blue-gain from 0 to 255 Red- gain from 0 to 255 User2... -
Page 13: Set Atr Level
Set the camera image characteristics such as brightness, contrast, sharpness, hue, and saturation (called “Gain” here) of the picture. The parameters of each can be set between 0 and 255. Use the mirror function to flip the camera image so that it is correctly orientated for viewing. -
Page 14: Set The Privacy Mask Area
Detect sense: Set the sensitivity level for motion detection. A higher value is more sensitive. Block Disp: When enabled, any movement detected will be tracked on-screen. Press Enter to enable or press the button again to cancel it. Monitor area: When enabled, a square grid is displayed on-screen. It can only be enabled if Block Disp is also enabled. -
Page 15: Set Day/Night Mode
Set Day/Night mode In the Setup menu, go to Day/Night and select the desired mode. The Day/Night mode has two options: Auto, Color and B/W. Select Color to manually set the camera to color (day) mode. Select Auto so that the camera can automatically switch between day (color) and night (black and white) mode. -
Page 16: Set The Camera Id
Set the camera ID In the Setup menu, go to Camera ID and press Enter to display the menu. The camera ID displayed on-screen can have up to 40 characters. Camera ID input line Command line To enter a character, move the cursor to the desired character and press Enter to select it. -
Page 17: Select The Language
Select the language Use this menu to select the OSD language. In the Setup menu, go to Language and select the desired language. There are only two languages available, English and Japanese. Reset camera settings Use this menu to reset the camera settings to factory default. In the Setup menu, go to Camera Reset and press Enter. -
Page 18: Specifications
Specifications Model TVC-6110-1-N(P) TVC-6120-1-N(P) Pickup device 1/3" Super HAD CCD II Total pixels NTSC: 811 × 508 / PAL: 795 × 596 Effective pixels NTSC: 768 × 494 / PAL: 752 × 582 Resolution 600 TVL Synchronization system Internal Internal / Line up Scanning system 2:1interlace IR cut... -
Page 19: Menu Map
Menu Map TruVision TVC-6110-1 / TVC-6120-1 Camera User Manual...