Denon AVR-E400 Owner's Manual page 149

GAudioH
Symptom
Audio is not output. • Check the connections for all devices.
• Check the speaker connections and configurations.
• Check whether the audio device power is turned on.
• Adjust the master volume.
• Cancel the mute mode.
• Check the connection with the playback device and select the
proper input source.
• Match the input mode and the terminal assigned to be the digital
input terminal.
• Disconnect the headphones. No sound is output from the
speakers when headphones are connected.
The volume does not • The maximum volume is set too low. Set the maximum volume
increase. using "Limit"on the menu.
• Power for external devices connected to the output connectors
of the unit may not be turned on. Check the power of connected
external devices.
No sound is • Check if the surround speakers are connected to the SURROUND
produced from terminals.
surround speakers.
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from audio from the surround back speakers.
surround back • Set "Speaker Config." – "Surr. Back" on the menu to something
speakers. other than "None".
• Set the sound mode to something other than "STEREO" and
"VIRTUAL".
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from front audio from the front height speakers.
height speakers. • Set "Speaker Config." – "Front Height" on the menu to something
other than "None".
DVD
Cause/Solution
9,
15,
81, 82, 83,
Symptom
Page
No sound is • Check the subwoofer connections.
1 0, 1 3, 1 4, produced from
1 6, 1 7, 1 8, subwoofer. • Turn on the subwoofer's power.
• Set "Speaker Config." – "Subwoofer" on the menu to "Yes".
19, 20
• If "Front" and "Center" for "Speaker Config." are set to "Large",
and "Subwoofer Mode" is set to "LFE", no sound may be output
from the subwoofers, depending on the input signal or selected
84, 85
sound mode.
–
DTS sound is not • Set "Decode Mode" on the menu to "Auto" or "DTS".
29, 93
output.
29, 93
Dolby TrueHD, DTS- • Make HDMI connections.
28, 93
HD, Dolby Digital
Plus audio is not
114
output.
• Check that "Speaker Config." – "Center" or "Surround" is set to
Dolby PLg mode or
130
other than "None". If the speaker system is 2.0/2.1-channel, this
DTS NEO:6 mode
cannot be selected. sound mode cannot be selected.
104
• When headphones are used, Dolby PLg or DTS NEO:6 cannot be
selected.
–
Audyssey MultEQ ® ,
• Switch the sound mode to other than "DIRECT" or "PURE
Audyssey Dynamic DIRECT".
EQ ® and Audyssey • When headphones are used, Audyssey MultEQ ® , Audyssey
–
Dynamic Volume ® Dynamic EQ ® and Audyssey Dynamic Volume ® cannot be selected.
cannot be selected.
• Run Audyssey ® Setup.
Audyssey Dynamic
116
EQ ® and Audyssey
Dynamic Volume ®
116
cannot be selected.
"Restorer" cannot • Check that an analog signal or PCM signal (Sample Rate=44.1/48
71
be selected. kHz) is input. For playback of multichannel signals such as Dolby
Digital or DTS surround, "Restorer" cannot be used.
116
• Switch the sound mode to other than "DIRECT" or "PURE
DIRECT".
116
146
Cause/Solution
81, 82, 83,
Page
84, 85
–
116
116, 118
114
9, 10
116
–
71
–
21, 86
103
71