USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed. INFLUENCE ALCOHOL. Model H3256/H3257 Spray Gun WORKSHOP CHILD UNDER DRUGS...
UNINTENTIONAL STARTING. Do not carry tool with hand on trig- ger and always disconnect from air when not in use. Model H3256/H3257 Spray Gun 17. DISCONNECT TOOLS before ser- vicing and changing accessories. 18. DO NOT OVERREACH. Keep proper footing/balance at all times.
NOT exceed the recommended inlet air pressure. Excessive pres- sure could cause the spray gun to burst or cause other internal equip- ment damage. 14. LOCAL authorities regarding exhaust and waste disposal requirements. PRESSURE. LAWS. Consult local Model H3256/H3257 Spray Gun...
Foreword We are proud to offer the Grizzly Model H3256/H3257 Spray Gun. These models are part of a growing Grizzly family of fine pneumatic tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation, and proof of Grizzly’s commit-...
21-50 PSI Less than 10 PSI (HVLP) Plastic 190mm Painted Metal Small to Medium Solids H3257 600ml Gravity 1.8mm 11 CFM 2.0-3.5 BAR 28.8-51 PSI Greater than 10 PSI Plastic 230mm Painted Metal Medium to High Solids Model H3256/H3257 Spray Gun...
Otherwise, filing a freight claim can be difficult. After you have unpacked the carton you should find the following: Model H3256 Inventory (Figure 1) A. Spray Gun ... 1 B. Cup 100ml ... 1 C. Cleaning Brush ... 1 D.
Trigger: Two stage trigger. Stage one only releases compressed air for blowing off the work piece. Stage two sprays material. Lightly squeeze the trigger for stage one. Squeeze the trigger all the way to spray. Model H3256/H3257 Spray Gun Controls Fluid Control Pattern Control...
Model H3256/H3257 Spray Gun Spraying The Model H3256/H3257 gravity feed spray gun set is designed to spray a wide variety of materials such as lacquers, stains, primers, multi-component paints, clear coats, acrylics, epoxies etc. It is ideal for auto body and woodworking projects.
Page 12
13. The spray stroke should have even con- sistency and parallel edges. If it doesn't, please refer to Troubleshooting on Page 17. CONTAMINATION HAZARD! Dispose of paint waste in a responsible man- ner! Follow manufacturer's recom- mendations and local laws regarding disposal. Model H3256/H3257 Spray Gun...
Page 15). Holes Stroke Figure 7. Set up for horizontal stroke direction with vertical fan pattern. Model H3256/H3257 Spray Gun Stroke Figure 8. Set up for vertical spray stroke with horizontal fan pattern. Rotating the pattern adjustment control in Figure 8 will give you a range between the two patterns in Figure 9.
H3174—Air Blow Gun with 2 Tips This air blow gun includes a safety tip and rubber tip for all normal air cleaning jobs. ⁄ " NPT . Figure 13. H3174 Air Blow Gun with 2 Model H3256/H3257 Spray Gun ⁄ " NPT. pressure regulator. Tips.
Fluid Tip Needle Atomizing Spring Figure 14. Disassembly for cleaning. Model H3256/H3257 Spray Gun 5. Unscrew the atomizing cap with your fingers and the fluid tip with the ser- vice wrench. The fully disassembled gun should look like Figure 14.
C. Trigger Pin D. Air Flow Control Valve E. Pattern Control F. Fluid Control Knob Allow the lubricant to coat threads, and run into gun body to lubricate all moving parts and seals. Figure 15. Lubrication points. Model H3256/H3257 Spray Gun...
1. No pressure at gun. 2. Fluid passages dirty. 3. Fluid control closed. 4. Out of paint. 5. Material too thick. Model H3256/H3257 Spray Gun Troubleshooting Solution 1. Tighten fluid tip or replace seat with new one. 2. Add material.
Page 18
1. Lower inlet air pressure. 2. Keep gun at recommended distance. 3. Slow down and maintain consistent, even parallel stroke. 1. Clean or replace both. 1. Install an in-line air filter. 2. Replace air line. Model H3256/H3257 Spray Gun...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 23
____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times.
Page 24
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...