Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H6331
Summary of Contents for Grizzly H6331
- Page 1 2-pc spray gun set instruction manual Copyright © May, 2009 By grizzly industrial, inC. Warning: no portion of this manual may be reproduced in any shape or form Without the Written approval of grizzly industrial, inc. #Cr11784 printed in China.
-
Page 3: Table Of Contents
6: maintenance ...14 Cleaning ...14 lubrication ...15 troubleshooting ...16 parts Breakdown h6331 ...18 large gun parts list h6331 ...18 large gun ...18 small gun parts list h6331 ...19 small gun ...19 Warranty and returns ...20 Model h6331 hVhp spray gun set... -
Page 4: Section 1: Safety
Model h6331 hVhp spray gun set WorKshop child under drugs... -
Page 5: Safety Instructions For Pneumatic Tools
Model h6331 hVhp spray gun set 17. disconnect tools before ser- vicing and changing accessories. 18. do not overreach. Keep proper footing/balance at all times. -
Page 6: Additional Safety Instructions For Hvhp Spray Guns
13. local authorities regarding exhaust and waste disposal requirements. Model h6331 hVhp spray gun set pressure. laWs. Consult local... -
Page 7: Section 2: Introduction
We are proud to offer the Grizzly Model Model H6331 HVHP 2-Pc Spray Gun Set. This model is part of a growing Grizzly fami- ly of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s com-... -
Page 8: Section 3: Set Up
Do not use a hose that has been used with an in-line oiler as the oil can contaminate the paint being sprayed or clog an in-line filter. assembly ⁄ " npt quick Model h6331 hVhp spray gun set... -
Page 9: Controls
Cap pattern Control trigger reservoir Quick release lock air supply port figure 2. Controls. Model h6331 hVhp spray gun set air supply port the paint Fluid Control stage one reservoir Fluid Control reservoir trigger... -
Page 10: Section 4: Operations
Model h6331 spray gun set is designed to spray low to medium viscos- ity liquids, like lacquers, stains, primers, multi-component paints, acrylics, epoxies, etc. - Page 11 Model h6331 hVhp spray gun set 9. Begin spraying 2-3 inches before the workpiece and continue through the end of the workpiece. Continue the motion for a few inches past the work until you are ready for the return stroke.
-
Page 12: Atomizing Cap And Fan Adjustments
(see figure 7) changes the shape of the spray pattern from a wide spray to a narrow spray, as shown in figure 8. pattern pattern Knob figure 8. Fan adjustment. Model h6331 hVhp spray gun set pattern pattern Knob... -
Page 13: Section 5: Accessories
800 psi and ⁄ " npt ends. figure 10. red rubber air hose. Model h6331 hVhp spray gun set h7274—campbell hausfeld™ pressure regulator this mini series regulator provides regu- lated output pressure of 0 to 125 psi for proper tool operation. -
Page 14: Section 6: Maintenance
14. large gun disassembled. 5. unscrew the atomizing cap with your fingers and the fluid tip with a wrench. the fully disassembled gun should look like figure 13 and 14. Model h6331 hVhp spray gun set spring needle reservoir spring... -
Page 15: Lubrication
8. Wipe the gun body with a lint free shop towel to dry. Model h6331 hVhp spray gun set lubrication lubricate the following areas with spray gun lube after cleaning: a. -
Page 16: Troubleshooting
1. no pressure at gun. 2. Fluid passages dirty. 3. Fluid control closed. 4. out of paint. 5. Material too thick. troubleshooting Model h6331 hVhp spray gun set solution 1. tighten fluid tip or replace seat with new one. 2. add material. 3. Clean 4. - Page 17 1. Work surface has oil spots, or paint, aka "Fish was improperly cleaned and eyes. primed. 2. Water or oil in the air line. Model h6331 hVhp spray gun set solution 1. reduce fluid pressure. 2. Keep gun at recommended distance. 3. slow down and maintain consistent, even parallel stroke.
-
Page 18: Parts Breakdown H6331
DESCRIPTION PH6331129 CONTROL SCREW NEEDLE ASSEMBLY PH6331136 PIVOT PIN PEC13M E-CLIP 5MM PH6331138 TRIGGER PH6331139 PLUG PH6331140 SPECIAL CONNECTOR PH6331141 TUBE PH6331142 SEAL PH6331143 CANISTER 1LITER CANISTER ASSEMBLY PH6331145 O-RING KIT PH6331146 UNIVERSAL WRENCH Model h6331 hVhp spray gun set... -
Page 19: Small Gun Parts List H6331
FLUID KNOB PH6331207 AIR INLET PLUG PORP008 O-RING 7.8 X 1.9 P8 PH6331209 COMPRESSION SPRING PH6331210 AIR VALVE SEAT Model h6331 hVhp spray gun set small gun 201-1 REF PART # 211 PH6331211 212 PH6331212 213 PH6331213 214 PH6331214 215 PH6331215...