Advertisement
Owner's Guide and Installation Manual
PELLA
NOTE TO THE INSTALLER: This Owner's Guide and Installation Manual is the property of the
homeowner. Please leave it with the homeowner upon completion of the installation.
Tools required
For safety reasons, the assistance of a second person is recommended when handling the door.
Read the legend below
For reference, the storm door assembly is illustrated on page 2.
Legend
1
2
3
MUST READ!
To order replacement parts, call
1-800-374-4758
or visit us at
www.pella.com
Please have your registration number
ready when you contact us either by
telephone or on the internet.
TROUBLE SHOOTING GUIDE
is located on page 12 of this manual
®
EXPRESS INSTALL
Tape Measure
Pencil
in order to easily follow along and install your storm door.
Follow the steps in order, from 1 to 35.
RED objects are the action items for that step.
Steps in BLUE apply to LEFT HINGE configurations ONLY.
(Hinge side will be determined in a later step.)
Steps in GREEN apply to RIGHT HINGE configurations ONLY.
(Hinge side will be determined in a later step.)
Instructions in this box style are IMPORTANT!
STORM DOOR MODELS
™
Power Drill with
3/32" drill bit
Lay door flat.
Before discarding the carton, make sure ALL parts are
accounted for -- check in carton roll-ups.
Loose
Parts
Carton
Roll-up
The carton material is recyclable
Part Number:
Phillips
Scissors
Screwdriver #2
NEW
Installation
Procedure.
Follow this manual for
a fast and proper
installation.
Loose Parts
(In Roll-up)
Hardware
Kit(s)
33258
Carton
Roll-up
Advertisement
Table of Contents
Related Manuals for Pella 6000
Summary of Contents for Pella 6000
- Page 1 33258 Part Number: Owner’s Guide and Installation Manual ® PELLA EXPRESS INSTALL STORM DOOR MODELS ™ NOTE TO THE INSTALLER: This Owner's Guide and Installation Manual is the property of the homeowner. Please leave it with the homeowner upon completion of the installation.
- Page 2 Storm Door Components NOTE: Actual door styles may vary from illustrations, however, the installation steps will be the same. Screw Cover Strips Header Frame Door Hardware Kit Door Closers Includes mounting screws and some Latch Mounting Frame handle components Mounting Glass/Screen Frame Retainer Strips...
- Page 3 Remember START this is the Your Installation INTERIOR SIDE of the door g l a a n d Turn door s c r e e n over. Remove shipping clips. Remove glass and screen. Align outer edges ... THEN, Predrill the FIRST, center align with face two holes.
- Page 4 Continued from Page 3 This is the TOP of Your Position door for Door In s id e LEFT hinge or F a c in g RIGHT hinge. Right RIGHT HINGE DOORS Hinge position metal plate Illustrated on this side. LEFT HINGE DOORS position metal plate on this side.
- Page 5 Continued from L E F T H IN G E Page 4 R IG H T H IN G E D o o rs O n ly D o o rs O n ly S LI D E To Th is S id e S L ID E T o T h is S id Set door in opening (resting on bo om spacer from step 10).
- Page 6 Continued from Install horizontal strips Page 5 Horizontal first (top then bottom) Retainer Strip Install Install Both Both Left and Vertical Right Retainer Install glass Bottom Strip panel. IMPORTANT: Hold glass in place while installing retainer strips. Secure with retaining strips. Predrill the five hole locations.
- Page 7 Continued from page 6 Break-off Tab (Remove if necessary) Position top mounting frame. Note: if you have interference with siding, remove the Leave this break-off tab with a plate in pliers, then caulk along place the back surface, for protection from rain. Right Hinge Illustrated...
- Page 8 Continued Remove the two hole plugs from from the closer bases. Hardware Instruction Insert into the factory drilled holes near the top corners of the door. Hole Plugs Qty. Break off of closer base LEFT HINGE Install Closers Determine which on This Side.
- Page 9 Continued To Use: Locate from Open the door, Touch ‘n Hold™ the top Closer then tap the button. Button Page 8 Touch ‘n Hold™ To Close: Button bo om Nudge the door BOTTOM closers. open slightly. Closer Slide top and bo om closers onto their bases.
- Page 10 Continued from page 9 Close door. j u s Adjust bo om t e n expander to lightly e t i contact the sill. t h e Sweep Sill Install screw cover strips Angled Edge Points Away (1 Horizontal, 2 Vertical). From Door Hint: With the angled edge in place, run your finger down the length of the inner edge to snap in place.
-
Page 11: Care And Maintenance
Note: DO NOT use ammonia-based cleaners on brass or other metallic finish handles. If your Pella door includes a solid brass handle, the brass is polished and sealed with a clear coating by the Cleaning &... - Page 12 20 years after the purchase date. The purchaser will be responsible for transporting the door to and from the nearest Pella storm door dealer. Should the door be determined to be defective in material or workmanship AFTER 20 years from the purchase date, the original purchaser may buy one new Pella storm door at 50% of the then-current manufacturer’s suggested list price for as long as the original purchaser owns the...