Consulting Programmed Actions; Tips And Tricks - Daikin EKHBH016BB3V3 Operation Manual

Consulting programmed actions

Consulting space heating or domestic water heating actions
Consulting space heating or domestic water heating is carried out as
follows.
INFORMATION
Returning to previous steps in this procedure is done by
pressing the pr button.
Press the < button.
1
The actual mode is blinking.
Use the pi and pj buttons to select the mode you want
2
to program (space heating h or domestic water heating
Press the < button to confirm the selected mode.
3
The actual day is blinking.
Select the day you would like to consult by means of the pi
4
and pj buttons.
The selected day is blinking.
Press the < button to confirm the selected day.
5
The first programmed action of the selected day appears.
6 Use the pi and pj buttons to consult the other
programmed actions of that day.
This is called the readout mode. Empty program actions (e.g. 3
and 4) are not displayed.
By pressing the pr button several times, you return to previous
steps in this procedure and finally return to normal operation.
Consulting space cooling, quiet mode, or booster heater
(1)
mode
Consulting space cooling, quiet mode, or booster heater mode
carried out as follows.
INFORMATION
Returning to previous steps in this procedure is done by
pressing the pr button.
Press the < button.
1
The actual mode is blinking.
Use the pi and pj buttons to select the mode you want
2
to consult (space cooling c , quiet mode
(3)
mode m
).
The selected mode is blinking.
3 Press the < button to confirm the selected mode.
The first programmed action is displayed.
Use the pi and pj buttons to consult the programmed
4
actions.
This is called the readout mode. Empty program actions (e.g. 3
and 4) are not displayed.
By pressing the pr button several times, you return to previous
steps in this procedure and finally return to normal operation.

Tips and tricks

Programming the next day(s)
After confirming the programmed actions of a specific day (i.e. after
pressing the < button for 5 seconds), press the pr button once. You
can now select another day by using the pi and pj buttons
and restart consulting and programming.
Copying programmed actions to next day
In heating/domestic water heating program it is possible to copy all
programmed actions of a specific day to the next day (e.g. copy all
programmed actions from "1" to "2").
(1) Only applicable for tank with built-in electrical booster heater (EKHW*).
(2) Only applicable for tank with built-in electrical booster heater (EKHW*).
(3) Only applicable for tank with built-in electrical booster heater (EKHW*).
EKHBH/X016BB
Indoor unit and options for air to water heat pump system
4PW62573-1 – 10.2010
To copy programmed actions to the next day, proceed as follows:
Press the < button.
1
The actual mode is blinking.
Use the pi and pj buttons to select the mode you want
2
to program.
The selected mode is blinking.
You can leave programming by pressing the pr button.
3 Press the < button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to copy to the next day by means
of the pi and pj buttons.
The selected day is blinking.
w )
You can return to step
5 Press the < and pr buttons simultaneously for 5 seconds.
After 5 seconds the display will show the next day (e.g. "2" if
"1" was selected first). This indicates that the day has been
copied.
You can return to step
Deleting one or more programmed actions
Deleting one or more programmed actions is done at the same time
as storing the programmed actions.
When all actions for one day have been programmed, make sure that
the display shows the highest action number you would like to save.
By pressing the < button for 5 seconds, you store all actions except
those with a higher action number than the one that is displayed.
E.g. when the < button is pressed when action number 3 is
displayed, actions 1, 2 and 3 are stored but 4 is deleted.
Deleting a mode
Press the < button.
1
(2)
is
The actual mode is blinking.
Use the pi and pj buttons to select the mode you want
2
to delete (space cooling c, quiet mode
mode
The selected mode is blinking.
3 Press the < and ba button simultaneously for 5 seconds to
delete the selected mode.
Deleting a day of the week (space heating or domestic water
s , or booster heater heating mode)
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to delete (space heating h or domestic water heating
The selected mode is blinking.
3 Press the < button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to delete by means of the pi
and pj buttons.
The selected day is blinking.
5 Press the < and ba button simultaneously for 5 seconds to
delete the selected day.
(4) Only applicable for tank with built-in electrical booster heater (EKHW*).
by pressing the pr button.
2
by pressing the pr button.
2
(4)
m ).
s , or booster heating
w ).
Operation manual
12