Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Cardo Systems SCALA RIDER Q2 PRO
Summary of Contents for Cardo Systems SCALA RIDER Q2 PRO
-
Page 1: User Guide
™ ™ ™ communication in motion User Guide... - Page 2 © Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners.
- Page 3 INTRODUCTION CONTENTS OF RETAIL BOX Congratulations, and thank you for choosing the scala rider Q2 Bluetooth® Headset. This Manual will help you operate the headset, but Volume Up / you should first familiarize yourself with the Bluetooth® functionality of Headset Forward MP3 Music your cellular phone and/or GPS device before using the scala rider Q2...
- Page 4 SET UP AND CONFIGURATION Wall Charger Allen Wrench Velcro Pads MP3 Cable Built-in FM radio Mobile phone MP3 Cable Holder & A2DP player connectivity Glue Plate Driver-to-Passenger Full-duplex Pre-moistened Towelette Intercom Connection Carry-Pouch Bike-to-Bike Intercom Microphone Sponges up to 700 m / 2,300 ft scala rider Q2 (in open terrain) other scala rider...
- Page 5 PRIMARY BUDDY PAIRING (requires two NOTE: If the Pairing process is not completed within two scala rider Q2 headsets*) minutes the headset will return to Standby mode. * Same process is applicable also for pairing with the Q2, i.e. the predecessor 1.
- Page 6 To Pair the scala rider Q2 to a Bluetooth Mobile When using an earlier scala rider headset as a Passenger headset, Voice Connect Intercom can be initiated only by Phone the scala rider Q2 headset. 1. Turn on your phone and make sure its Bluetooth function is Manual Connect Intercom can be initiated from either activated.
- Page 7 3. Search for Bluetooth headsets on your GPS device by following the device’s instructions. The headset will be listed as two screws on the Back Plate. “scala rider Q2 Pro “. Please consult your GPS device’s User 2. Slide the Back Plate between the internal Manual for more information.
- Page 8 proceed as follows. 1. Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp’s back plate. a. Peel the foil cover from the adhesive Velcro pad and place the Velcro pad on the chosen 2. Determine the location on the helmet where the location opposite your mouth.
- Page 9 AUDIO SOURCES AND PRIORITIES ATTACHING AND REMOVING THE The different Audio Sources that are connected to the scala rider Q2 HEADSET FROM THE HELMET CLAMP are prioritized as follows: ATTACHING: Highest 1. Mobile phone Audio / GPS device (Incoming/outgoing calls , GPS audio and navigation instructions) Slide the headset downwards along the 2.
- Page 10 MC Button MC BUTTON CONNECT: TROUBLESHOOTING THE INTERCOM: Double tap the MC Button First, make sure your microphone is located properly in front of the A Buddy Intercom call will be established. To end the center of your mouth. Buddy Intercom call, double tap the MC Button again. The scala rider Q2 is designed for use in loud environments.
- Page 11 During Standby, press and hold the Volume Up Button for STATUS LIGHT STATES three seconds and you will hear a beep: • One beep – Voice Connect set to Primary Buddy None Headset is off • Two beeps – Voice Connect set to Secondary Buddy Mobile phone Pairing mode Alternating red and Blue flashes...
- Page 12 strongest signal available for the FM station you wish to listen to, no To save this station, refer to the following section. matter where you are riding. This allows you to leave your hands on To continue searching, press the Volume Up or Volume Down Button the handlebars at all times with no need to adjust the radio station again for three seconds.
- Page 13 3. Place the Back Plate on top of the MP3 cable holder and secure all parts together using the Allen screws that were previously 4. After a few seconds the MP3 Player will list “scala rider Q2 Pro ” as removed, as shown in photo.
- Page 14 cable holder. to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency Make sure that the cable plug clicks into place. energy and, if not installed and used in accordance with the instructions, may cause 7.
-
Page 15: Waiver And General Release
interference by one or more of the following measures: in traffic. • Reorient or relocate the receiving antenna. You are irrevocably releasing, indemnifying from any liability, loss, claim and ex- • Increase the separation between the equipment and receiver. pense (including attorneys fees) and holding Cardo harmless for any bodily injuries, •... - Page 16 and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGE- MENT.