Adjusting And Storing The Time Correction; Recalling The Stored Time Correction Settings - Alpine CDA-9833R Owner's Manual

Time Difference Table
Time
Delay Distance
Difference
Number cm (inch)
(ms)
0 0.0 0.0
1 0.1 3.4 (1-3/8")
2 0.2 6.9 (2-3/4")
3 0.3 10.3 (4-1/16")
4 0.4 13.7 (5-3/8")
5 0.5 17.2 (6-13/16")
6 0.6 20.6 (8-1/8")
7 0.7 24.0 (9-7/16")
8 0.8 27.4 (10-13/16")
9 0.9 30.9 (12-3/16")
10 1.0 34.3 (13-1/2")
11 1.1 37.7 (14-13/16")
12 1.2 41.2 (16-1/4")
13 1.3 44.6 (17-9/16")
14 1.4 48.0 (18-7/8")
15 1.5 51.5 (20-1/4")
16 1.6 54.9 (21-5/8")
17 1.7 58.3 (22-15/16")
18 1.8 61.7 (24-1/4")
19 1.9 65.2 (25-5/8")
20 2.0 68.6 (27")
21 2.1 72.0 (28-3/8")
22 2.2 75.5 (29-11/16")
23 2.3 78.9 (31-1/16")
24 2.4 82.3 (32-3/8")
25 2.5 85.8 (33-3/4")
26 2.6 89.2 (35-1/8")
27 2.7 92.6 (36-7/16")
28 2.8 96.0 (37-3/4")
29 2.9 99.5 (39-13/16")
30 3.0 102.9 (40-1/2")
31 3.1 106.3 (41-7/8")
32 3.2 109.8 (43-1/4")
33 3.3 113.2 (44-9/16")
34 3.4 116.6 (45-7/8")
35 3.5 120.1 (47-5/16")
36 3.6 123.5 (48-5/8")
37 3.7 126.9 (49-15/16")
38 3.8 130.3 (51-5/16")
39 3.9 133.8 (52-11/16")
40 4.0 137.2 (54")
41 4.1 140.6 (55-3/8")
42 4.2 144.1 (56-3/4")
43 4.3 147.5 (58-1/16")
44 4.4 150.9 (59-3/8")
45 4.5 154.4 (60-3/4")
46 4.6 157.8 (62-1/8")
47 4.7 161.2 (63-7/16")
48 4.8 164.6 (64-3/4")
49 4.9 168.1 (66-3/16")
50 5.0 171.5 (67-1/2")
22
-EN
Time
Delay Distance
Difference
Number cm (inch)
(ms)
51 5.1 174.9 (68-7/8")
52 5.2 178.4 (70-1/4")
53 5.3 181.8 (71-9/16")
54 5.4 185.2 (72-7/8")
55 5.5 188.7 (74-1/4")
56 5.6 192.1 (75-5/8")
57 5.7 195.5 (77")
58 5.8 198.9 (78-5/16")
59 5.9 202.4 (79-11/16")
60 6.0 205.8 (81")
61 6.1 209.2 (82-3/8")
62 6.2 212.7 (83-3/4")
63 6.3 216.1 (85-1/16")
64 6.4 219.5 (86-3/8")
65 6.5 223.0 (87-3/4")
66 6.6 226.4 (89-1/8")
67 6.7 229.8 (90-1/2")
68 6.8 233.2 (91-13/16")
69 6.9 236.7 (93-3/16")
70 7.0 240.1 (94-1/2")
71 7.1 243.5 (95-7/8")
72 7.2 247.0 (97-1/4")
73 7.3 250.4 (98-9/16")
74 7.4 253.8 (99-7/8")
75 7.5 257.3 (101-1/4")
76 7.6 260.7 (102-5/8")
77 7.7 264.1 (104")
78 7.8 267.5 (105-5/16")
79 7.9 271.0 (106-11/16")
80 8.0 274.4 (108-1/16")
81 8.1 277.8 (109-3/8")
82 8.2 281.3 (110-3/4")
83 8.3 284.7 (112-1/16")
84 8.4 288.1 (113-1/16")
85 8.5 291.6 (114-3/4")
86 8.6 295.0 (116-1/8")
87 8.7 298.4 (117-1/2")
88 8.8 301.8 (118-13/16")
89 8.9 305.3 (120-3/16")
90 9.0 308.7 (121-1/2")
91 9.1 312.1 (122-7/8")
92 9.2 315.6 (124-1/4")
93 9.3 319.0 (125-9/16")
94 9.4 322.4 (126-7/8")
95 9.5 325.9 (128-5/16")
96 9.6 329.3 (129-5/8")
97 9.7 332.7 (131")
98 9.8 336.1 (132-5/16")
99 9.9 339.6 (133-11/16")

Adjusting and Storing the Time Correction

Before performing the following procedures, refer to "About Time
Correction" (page 20).
1
Press and hold MENU for at least 2 seconds.
2
Press MENU to select Bass Focus mode or Time
Correction mode.
3
Press g or f to make time corrections.
Each press changes the mode as follows:
Bass Focus mode ↔ Time Correction mode
4
Press BAND/TEL. to select a speaker to be
adjusted.
CDA-9835R
F – L → F – R → R – L → R – R → SW – L → SW – R → F – L
CDA-9833R
Front – L → Front – R → Rear – L → Rear – R → SUBW – L →
SUBW – R → Front – L
5
Turn the Rotary encoder to adjust the desired
time correction value.
To store the adjusted contents
1) Press and hold, for at least 2 seconds, any one of the
preset button (1 or 6) into which you wish to store the
adjusted contents.
6
Repeat step 4 and 5 to set another speaker.
7
Press the Rotary encoder to confirm the
adjusted contents.
The adjusted contents are not stored if the Rotary encoder
is not pressed.
8
After setting, press and hold MENU for at least 2
seconds to return to normal mode, or press MENU
and select RETURN to return to normal mode.
• If no operation is performed in 15 seconds, the unit returns to
normal mode.

Recalling the Stored Time Correction Settings

1
Press and hold MENU for at least 2 seconds.
2
Press MENU to select Bass Focus mode or Time
Correction mode.
3
Press g or f to make time corrections.
Each press changes the mode as follows:
Bass Focus mode ↔ Time Correction mode
4
Press the preset buttons (1 through 6) that has
your desired time correction in memory.
5
Press and hold MENU for at least 2 seconds to
return to normal mode, or press MENU and select
RETURN to return to normal mode.
• Time Correction mode is automatically cancelled if no operation is
performed within 15 seconds.