Country; Basic Setup / Tv View Operation; Initial Setting - FUNAI TD6D-D4413DB Owner's Manual

Basic Setup / TV View Operation

Initial Setting

When you turn on this unit for the first time, you need to follow
these steps.
1
Press [STANDBY-ON
2
Turn the TV on. Select the input to which the
unit is connected.
"Initial Setting" will automatically appear.
3
Select your desired language for the OSD using
[K L]. Then press [ENTER OK] to go to the
next step.
OSD Language
English
Áúëãàðñêè
Èesky
Français
Deutsch
Magyar
4
Select your desired country for receiving your
local channels properly using [K L]. Then
press [ENTER OK] to go to the next step.
This setting is mainly for digital channels.

Country

France
Spain - Peninsula
Spain - Canary Islands
Germany
Italy
Switzerland
Czech Republic
Other
Digital channels cannot be received properly for the
countries not listed above.
In such case, select "Other".
5
Select your desired tuning type according to
your area using [K L], then press
[ENTER OK].
Auto Tuning
Make sure the antenna is
connected to "ANTENNA IN" jack.
Digital tuning
Digital & Analog tuning
Analog tuning
The unit will start getting channels available in your area.
Digital tuning:
Only the DVB channels receivable in your area are
automatically scanned and memorised.
Digital & Analog tuning:
Both analogue and DVB channels receivable in your area
are scanned and memorised automatically.
Analog tuning:
Only the analogue channels receivable in your area are
automatically scanned and memorised.
• If no channel has been memorised, the antenna
confirmation display will appear. Press [ENTER OK] to start
auto scanning again or press [RETURN BACK] to cancel
the initial settings.
20
EN
].
6
After finishing channel setting, "Clock Setting"
will appear.
Clock Setting
01 / 01 / 2010 (FRI)
• The current date and time will appear automatically.
• If the current date and time are correct, press
[RETURN BACK] to exit, if they are incorrect, press
[ENTER OK] and follow to "
page 71.
Note
• After "Initial Setting", if you need to unplug the mains cable,
make sure to turn off the power first and leave it in standby
mode for at least 1 minute before attempting to unplug.
Otherwise, it may cause data loss.
If you want to set each item of "Initial Setting" again, you can
set them at "General Setting".
• Refer to " OSD Language (Default: English)" on page 70.
• Refer to "Country Setting" on page 23.
• Refer to "Auto Tuning (DVB & ANALOG)" on page 21.
• Refer to "Auto Tuning (ANALOG)" on page 21.
• Refer to "Auto Tuning (DVB)" on page 23.
• Refer to "Clock" on page 71.
Also you can customize the memorised channel at "General
Setting".
Refer to following pages for details.
• Refer to "Manual Tuning (ANALOG)" on page 21.
• Refer to "Manual Tuning (DVB)" on page 23.
• Refer to "Skip a Preset Channel" on page 22.
• Refer to "Move" on page 22.
Selecting the TV Aspect Ratio
Use this feature to adjust the aspect ratio of the video source
which is different from your TV's ratio to fit your TV monitor
without distorting the picture.
1
In stop mode, press [SETUP]. Select "General
Setting" using [K L], then press [ENTER OK].
2
Select "Video" using [K L], then press
[ENTER OK].
3
Select "TV Aspect" using [K L], then press
[ENTER OK].
TV Aspect
Video Out
4
Select the desired option using [K L], then
press [ENTER OK].
TV Aspect
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
5
Press [SETUP] to exit.
0 : 00
Clock Setting" on