Programming A Different Component Into A Multi Control Button (Vsx-839Rds Only); Checking Preset Codes (Vsx-839Rds Only) - Pioneer VSX-839RDS Operating Instructions Manual

Remote Control of Other Components
Programming a Different Component into a MULTI
CONTROL button (VSX-839RDS only)
This feature changes a selected Multi Control button to a different component. For example, if you don't have a second
TV, but you do have a second DVD, you could reassign the TV Multi Control to VCR so that VCR control buttons are
available when you select TV.
SOURCE RECEIVER
DVD TV
MULTI CONTROL
CD CD-R
4
1 2
LOUDNESS VIDEO SELECT
4 5
INPUT ATT DIGITAL NR
2
7 8
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT
+10 0
EFFECT/CH SEL
RECEIVER
1
TV VOL TV
TV CONTROL
TVFUNK
4
CHANNEL
TUNE
ST
ENTER
TUNE
TOP MENU
D.ACCESS BAND
& ‹
MPX DISPLAY
¶
!

Checking Preset Codes (VSX-839RDS only)

SOURCE RECEIVER
DVD TV
MULTI CONTROL
CD CD-R
1 2
VIDEO SELECT
LOUDNESS
4 5
INPUT ATT DIGITAL NR
2
7 8
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT
4
+10 0
EFFECT/CH SEL
RECEIVER
1
TV VOL TV
TV CONTROL
TVFUNK
4
CHANNEL
TUNE
ST
ENTER
TUNE
TOP MENU
D.ACCESS BAND
& ‹
MPX DISPLAY
¶ !
RETURN SETUP CLEAR
RECEIVER DIRECT CONTROL
MIDNIGHT DSP STEREO
THX
ADVANCED STANDARD MUTE
2
/ DTS / MPEG
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
74
En
1 Press RECEIVER.
VCR VCR
2 Press REMOTE SETUP and hold for three seconds.
1 2
3,5
TUN TVC
3
MULTI CH INPUT
6 3 Press the MULTI CONTROL button which you
FL DIMMER
4
9
DISC
MASTER VOLUME
4 Press 9, 9, then 2.
¢
ST
5 Press the MULTI CONTROL button which you
MENU
CLASS
*
RF ATT
⁄
To check which preset code is associated with a Multi Control button:
1 Press RECEIVER.
VCR VCR
1 2
3
TUN TVC
2 Press REMOTE SETUP and hold for three seconds.
3 5-8
MULTI CH INPUT
6
FL DIMMER
4
9
3 Press the MULTI CONTROL button you want
DISC
MASTER VOLUME
4 Press 9, 9 then 0.
¢
ST
MENU
5 Press 1.
CLASS
*
RF ATT
⁄
AUDIO
FUNCTION
6 Press 2.
Î
7 Press 3.
8 Press 4.
This switches the remote to the surround setup mode.
The LED on the remote will blink twice.
want to change.
For the example above, press VCR.
The LED on the remote will blink twice.
want to be duplicated.
In the above example, press TV. The LED will blinks twice. The TV
button will now make the remote function as a VCR controller.
Remember to assign the correct preset code for your equipment
(the default is for Pioneer equipment).
This switches the remote to the surround setup mode.
The LED on the remote will blink twice.
to check the preset code for.
Each preset code consists of four digits, for example 1329. Each
digit will be represented by a series of blinks on the remote's
LED—3 blinks to represent the digit "3", etc.
The blinking LED indicates the left-most digit of the preset code
("1" in the example above).
The blinking LED indicates the next digit of the preset code ("3" in
the example above).
The blinking LED indicates the next digit of the preset code ("2" in
the example above).
The blinking LED indicates the right-most digit of the preset code
("9" in the example above).