Final Finishing; Mantels; Cabinet Installation; Electrical Connections - Lennox REFLECTIONS LSE-36R Installation And Operation Instructions Manual

(Logs Not Shown
For Clarity)
Tabs
(Back)
Figure 13

FINAL FINISHING

FINISH TO YOUR TASTE
There are a wide variety of "finished looks" for
these fireplaces, from formal wall decor with
elaborate mantels to rustic wood paneling or
warm brick facings.
Materials like stone, tile, brick, etc., may over-
lap the black front facing. Do not extend these
materials beyond the black facing and into the
firebox area. Do not cover outlet or face
opening. Be sure not to interfere with the
installation and operation of glass doors or
block the lower grilles. Use caulking material
to seal the black metal facing to the surround
material on the finished wall.
Combustible materials may overlap the face of
the fireplace as long as they do not encroach
into the firebox opening ( see Figure 14 ).
Sidewall May
Be At Any
Distance From
The Face
Opening
Hearths And
Mantles May
Overlap The
Black Face.
DO NOT Block
The Lower Grille
Figure 14
8
Tabs
Glass
Front Lip
Up
(Front)
(Front)
HEARTH
A hearth is not mandatory, but it is recom-
mended for aesthetic purposes. Hearth exten-
sion must not block the removable grille com-
ponent ( see Figure 15 ).
HEARTH EXTENSIONS
5"
Maximum Thickness Of Hearth Extension
Above The Base Of The Appliance
Figure 15
Secure the hearth extension to the floor to
prevent possible shifting.
Cold climate installation recommendation:
When installing this fireplace against a non-
insulated exterior wall or chase, it is manda-
tory that the outer walls be insulated to con-
form to applicable insulation codes.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Do Not Cover Or Obstruct

MANTELS

Combustible and Non-combustible mantels
may be installed at any height above the appli-
ance opening.
CLEARANCE TO COMBUSTIBLES
Sides: 0 mm - 0 inches
Floor: 0 mm - 0 inches
Top: 0 mm - 0 inches
CABINET INSTALLATIONS
Cabinets are available from your dealer which
allow for fast, convenient installation of your
fireplace against existing walls.

ELECTRICAL CONNECTIONS

A 15AMP, 120 Volt, 60Hz circuit, with a prop-
erly grounded outlet, is required. Preferably,
the fireplace will be on a dedicated circuit, as
other appliances on the same circuit may cause
the circuit breaker to trip, or the fuse to blow,
when the heater is in operation.
The unit comes standard with a 5 ft. (1524mm)
long three wire cord, exiting the left side of the
fireplace. Plan the installation to avoid the use
of an extension cord. If an extension cord
must be used, it must be a minimum 16AWG,
three wire with grounding type plug, and con-
nector and rated not less than 2025 Watts.
A new electrical outlet can be installed inside the
frame construction, if permitted by local codes.
The EV-220 kit is available from your dealer that
will allow this appliance to be connected to a
220V 15 Amp supply.
The kit contains a power cord connector and
heater element for a standard 220V single phase
connection.
Refer to the electrical diagram on page 11.
ELECTRICAL SPECIFICATIONS
Voltage: 120VAC,60Hz 240VAC,60Hz
Total Amps: 12.5 Amps
Total Watts: 1500 Watts
Heater Rating: 1300 Watts
WARNING: ELECTRICAL OUTLET WIR-
ING MUST COMPLY WITH LOCAL
BUILDING CODES AND OTHER APPLI-
CABLE REGULATIONS TO REDUCE THE
RISK OF FIRE, ELECTRICAL SHOCK AND
INJURY TO INDIVIDUALS.
12.5 Amps
3000 Watts
2500 Watts