Table of Contents
Advertisement
13.2
EQUIPMENT WARNING LABELS
ATERIAL - VINYL OR POLYESTER
DO NOT attempt to install, operate, maintain or dispose of this equipment until you have read and under-
EMPERATURE - MINUS 20 TO 100 deg. C
DHESIVE - V23 OR EQUIV.
stood all of the product warnings and user directions that are contained in this instruction manual.
UST RESIST OIL SOLVENTS
LL MATERIALS USED MUST
Shown below are examples of warning labels that may be found attached to the equipment. DO NOT re-
E UL RECOGNIZED
ARNING AREA BACKGROUND COLOR: ANSI DANGER RED
move or cover any of the labels. If the labels are damaged or if additional labels are required, contact your
ARNING AREA TEXT COLOR: ANSI WHITE
TOSHIBA representative for additional labels.
EXT AREA BACKGROUND COLOR: ANSI WHITE
EXT AREA TEXT COLOR: ANSI BLACK
The following are examples of the warning labels that may be found on the equipment. The labels are
ORNER RADIUS: VENDOR STANDARD
there to provide useful information or to indicate an imminently hazardous situation that may result in seri-
ous injury, severe property and equipment damage, or death if the instructions are not followed.
(A) 48082
1.50
AC VOLTAGE
This UPS receives power from more
than one source. Disconnect all AC
sources before performing any service
or testing inside this unit
0.00
Figure 13-3 - 431M Cabinet
DRAWN:
CHECKED:
BC 6-10-98
TF 8-2-06
THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL
CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED
TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.
DATE
BY
13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.
52
DANGER
WARNING AREA
TEXT AREA
48082
Warning Labels
TITLE:
APPROVED:
DANGER LABEL
TF 8-2-06
MULTIPLE SOURCES
DRAWING NO.:
MATERIAL - VINYL OR POLYESTER
TEMPERATURE - MINUS 20 TO 100 deg. C
ADHESIVE - V23 OR EQUIV.
MUST RESIST OIL SOLVENTS
ALL MATERIALS USED MUST
BE UL RECOGNIZED
WARNING AREA BACKGROUND COLOR: ANSI DANGER RED
WARNING AREA TEXT COLOR: ANSI WHITE
TEXT AREA BACKGROUND COLOR: ANSI WHITE
TEXT AREA TEXT COLOR: ANSI BLACK
CORNER RADIUS: VENDOR STANDARD
(B) 40308
4.50
0.00
SCALE:
FULL
0
REV:
48082
DRAWN:
WLM 3-9-11
THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL
CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED
TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.
ECN
DATE
BY
13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.
4300 Series Ancillary Cabinets Installation and Operation Manual
DANGER
HAZARDOUS VOLTAGES
Hazardous voltages are used in the operation
of this equipment and could cause severe personal
injury or loss of life.
The following precautions should be observed to
reduce the risk of injury or death.
Only qualified technicians familiar with this equipment and the
information supplied with it should be permitted to install and
operate this equipment.
Installation of electrical equipment must be done in
accordance with National Electrical Code and any other state
or local codes. Proper grounding and conductor sizing must
be installed for safe operation.
During operation, keep all covers in place and cabinet
doors shut.
When performing visual inspections and maintenance, if
possible, be sure the MBS is turned off and the incoming
AC feed is turned off and locked out.
The UPS and Battery Cabinet will have hazardous
voltages present even after the AC feed is turned off.
If it is necessary to make measurements with the power
on, do not touch any electrical connection points. Remove
all jewelry from wrists and fingers. Make sure test equipment
is in good, safe operating condition.
While servicing, stand on some type of insulation, and be
sure not to be grounded.
Follow the safety instructions given in the equipment manual
carefully and observe all danger, warning and caution notices.
TITLE:
CHECKED:
APPROVED:
ZIR 3-10-11
WLM 3-10-11
WARNING ARE
TEXT AREA
40308
64818
DANGER LABEL
GENERAL - MBS
DRAWING NO.:
Advertisement
Table of Contents
