The Installation Space; Dimensions And Clearances - GE 36" Built-In Bottom-Freezer Installation Instructions Manual

Design Guide
THE INSTALLATION SPACE
The finished
cutout width
must be
B5-1/2".
35-1/2"
Finished W idth
Wall View
84-1/2" max 75" From
83-1/2" min Floorto Bottom
Finished of ElectricalArea
0per
Water And Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot exceed
the 24" installation depth shown. The top case trim
overlaps the bottom of the soffit.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be located
on rear wallas shown.
Note:GFI(ground fault i nterrupter)is not
recommended.
• Water line c an enter theopeningthrough thefloor
or buckwall. R outeGE SmartConnect
T M
kit or 1/4"O.D.
coppertubing between thecoldwaterline a nd the
waterconnection locution. The tubing should be
long enough to extend to the front of the refrigeratoE
Installation of an easily accessible shut-off valve in
the water line is required.
DIMENSIONS AND CLEARANCES
35"
CaseWidth
,_ CaseDepth
T _84"From
"83-1/2" Floorto
at TopFlame
Rear m*
_._36"_ Frame to
r-
Frame Width
DepthIncludingHandles:
26-7/8"FlamedModels
27-3/4" Stainless Steel Models
28-11/16"Professional StyleMe@is
25-3/8"Framed Me@is
25-3/4"StainlessSteel Models
* Shipping height. The
refrigerator con be
adjusted to fit into o
cutout that is 83-1/2"
min. to 84-1/2" max.
height. Note that the top
case trim at the front is
1/2" higher and will
overlap upper cabinetry
or soffit. Use leveling legs
and wheels for o
maximum 1" height
adjustment.
Product Clearances
These refrigerators are equipped with a 2-position door
stop. The factory set 1BO ° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
130"Door S wing
'L
\
\,
\\
130°
......... J_
T
23-7/8"
Behind
90° Door Swing Frame
136-3/4"
I
I
*4" Stainless
90°
"_- .... ! and Framed
models.
5" Pro Series
*Min. Distance to Wall
Allow 25" minimum clearance for o full 1BO ° door
swing. Allow 15" for pan removal.
For o 90° door swing, allow 4" min. clearance to o wall,
for framed and stainless steel models. Allow 5" min.
clearance for professional style models. If the 90° door
stop position is used, pan access is maintained, but pan
removal is restricted.
See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators, side by side,
the installation space must be 71-1/2" wide.
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width.
• The water and electrical locations for each product
must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply is
recommended for each product.
84-1/2"max
83-1/2"rain
Finished
Opening
--- 71-1/2"Finished Width_
,_2-5/16" _ WallView
_F_[lectrJcal-_ _ 24-3/16"
10" 10"
-24" CutoutDepth
3-1/2" 3-1/2" 3q/2" 3-1/2"
,_ 5,_5,,_
75" From
Floorto Bottom
of Electrical Area
Water Supply