1. Manuals
  2. Brands
  3. Garmin Manuals
  4. GPS
  5. GPS 17 Series
  6. Installation instructions manual

Garmin GPSMAP 2110 Installation Instructions Manual

Garmin gps receiver user manual
Hide thumbs Also See for GPSMAP 2110:
Table of Contents

Advertisement

Quick Links

See also: Instruction and Installation Manual
GPSMAP
®
2106/2110
& GPS 17
installation instructions
Graphic to be
replaced

Advertisement

Table of Contents
loading

Related Manuals for Garmin GPSMAP 2110

Summary of Contents for Garmin GPSMAP 2110

  • Page 1 GPSMAP ® 2106/2110 & GPS 17 installation instructions Graphic to be replaced...

  • Page 2: Safety Information

    Limited Warranty This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will at its sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost.
  • Page 3 Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check first to see what is on the opposite side of the surface. Mount the GPSMAP 2106/2110 in a location that provides a clear, glare-free view of the display and easy operation of the controls.
  • Page 4 NSTALLATION NSTRUCTIONS Surface Mounting the GPSMAP 2106/2110 Tools • Drill and drill bit • Screwdriver • Pencil • Mounting hardware (not included) NOTE: Mounting hardware (fasteners) not included. Mounting holes are 5/16" (7.9 mm) in diameter. To install the bail mount and unit: 1.
  • Page 5 • Sockets or wrenches • Hammer • Center punch To flush mount the GPSMAP 2106/2110: 1. Trim the Flush Mount Template, and tape it in the location you want. 2. Using the center punch, indent the center of each mounting hole location.

  • Page 6: Installing The Gps

    The GPS 17 connects to the 18-pin Power/Data Cable on the GPSMAP 2106/2110 and provides the GPS/WAAS signal for the unit. If two or more GPSMAP 2106/2110 units are installed, only one GPS 17 needs to be installed. To ensure the best reception, mount the GPS 17 in a location that has a clear, unobstructed view of the sky in all directions.
  • Page 7 3. Use the enclosed screws to secure the mount to the base. Attaching the Pole Mount to the GPS 17 Align Notch GPSMAP 2106/2110 & GPS 17 To mount the GPS 17 with the cable run outside the mount: 1. Place the cable in the vertical slot along the side of the base of the unit.

  • Page 8: Wiring And Cables

    Wiring and Cables The GPSMAP 2106/2110 comes with an 18-pin Power/Data cable. For some installations, it may be necessary to drill 1.25" (31.7 mm) holes to route the connector end of the cables. Garmin rubber grommets are provided to cover the installation holes (see below). Wiring instructions are found on the following pages.
  • Page 9 2. Use a standard pair of pliers to fully depress the red button into the connector. 3. Wipe the excess water repellent gel from the connector. The following diagram shows CANet wiring for the GPSMAP 2106/2110. Notes: * Connect the drain wire only on one side.

  • Page 10: Power/Data Cable Wiring

    Power/Data Cable Wiring The following pages contain several wiring diagrams. The first diagram on the next page is a simple diagram showing the GPSMAP 2106/2110 MFD using the 18-pin Power/Data wiring harness and the GPS 17. If two GPSMAP 2106/2110 units are installed and connected, only one GPS 17 antenna needs to be installed.
  • Page 11 ������ ������ ��������� ������ ������ ��������� GPSMAP 2106/2110 and NMEA Device with Sonar Output or VHF Radio with DSC ������ ������ ��������� ������ ������ ��������� GPSMAP 2106/2110 & GPS 17 10-33 VOLTS DC WIRE COLOR FUSE BLACK ORANGE GREEN �...
  • Page 12 Optional Alarm Wiring The GPSMAP 2106/2110 has an alarm circuit that can be used with a lamp, a horn, or both to alert you when the unit displays a message. The alarm circuit pulls low when the alarm sounds. The alarm does not have to be wired for the unit to function. The maximum current is 100 milliamps.
  • Page 13 Final Wiring Connection After all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the GPSMAP 2106/2110. The 5-pin port on the right side is intended for future interfacing features and does not require connection at this time.
  • Page 14 NSTALLATION NSTRUCTIONS GPSMAP 2106/2110 & GPS 17...
  • Page 15 NSTALLATION NSTRUCTIONS Flush Mount Drilling Template Drill using a 11/64" (4.5 mm) drill bit Drill this 3/4" (19 mm) hole if the coax is going to be installed through the mounting panel GPSMAP 2106/2110 & GPS 17...
  • Page 16 © Copyright 2006 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151 Street, Olathe, Kansas 66062, U.S.A. Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Garmin Corporation No. 68, Jangshu 2 Road, Shijr, Taipei County, Taiwan www.garmin.com...

This manual is also suitable for:

Gps 17Gpsmap 2106

Table of Contents