The Controls - Ariston Washer Manual

Start and Programs

The Controls

PROGRAMS knob
! Warning, if after pressing the Start/Pause button
the programs knob position has changed, the new
position will NOT change the program selected.
To change the program: Press the Start/Pause button
to pause the program - the light flashes amber to indicate
the program is paused. Select the new program and
any options required - the light will flash green. Press
the Start/Pause button and the new program will
start.
OPTION buttons / lights
These buttons are used to customize the selected
program to your requirements. A program must have
been selected on the programs knob before an option
can be selected. Not all options are available for all
programs (see Start and Programs). If an option is not
available and you press the button, the buzzer (alert)
will beep three times. If the option is available there
will be one beep and the option light next to the
button lights to confirm the selection.
After the Start/Pause button has been pressed only
the Pre Care and Post Care options can be changed.
Delay Start
The start of some programs (see Start and Programs)
can be delayed for up to 24 hours.
Press this button, the display shows
option light comes on. Press again and a 1 hour delay
is selected and the display indicates 1hr, each further
press of the button adds 1hr to the delay. When 24hr is
displayed a further press and the display shows
and after a couple of seconds cancels the delay.
You can also cancel the delay by pressing the On/Off
button .
Pre Care
This option is only available if a delayed start has
been selected. It tumbles the clothes occasionally
during the delayed period to help prevent creases
developing.
High Heat
Available for Timed Drying programs. Press this
button and a high heat setting is selected and the light
alongside the button comes on.
Timed programs have a default of low heat, if the light
alongside the button is on then pressing the button
selects a low heat setting and the light goes out.
Post Care
When available and selected, the clothes are
occasionally tumbled after the end of the drying and
air fluff cycles,
to help prevent creases developing should you not be
available to remove the load immediately the program
is complete.
The display shows either the amount of time delay
remaining or an indication of the amount of time left for
a drying program.
The delay time is displayed in hours and counts down
each minute.
The time to end is displayed in hours and minutes and
counts down each minute, this time includes the air
fluff phase. When timed programs are selected the
time displayed throughout the cycle is the actual time
remaining.
When a sensing program is selected the time
displayed is an estimate of the time remaining. When
the program is selected the display shows the time
required to dry a full load, after around 10 minutes the
controller calculates a better estimate of the cycle
time.
The colons between the hours and minutes in the
display flash to show that the time is counting down.
When the program finishes its air fluff phase the
display will show
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by
a fault code number (see Troubleshooting).
Opening the door (or pressing the Start/Pause button
during a program will stop the dryer and have the
OFF
and the
following effects:
OFF
If you have a power outage, switch off the power or
remove the plug, press the Start/Pause button and the
program will resume.
DISPLAY
E88
.
Door Opening
The Start/Pause light flashes amber.
During a delay phase the delay will continue
to count down. The Start/Pause button
must be pressed to resume the delay program.
The progress lights will change to show
current status.
During the drying part of the program, the
time to end count continues but the colons
do not flash. The Start/Pause button
be pressed to resume the program. The
progress lights will change to show the
current status.
During the post care phase of a drying
program the program will finish. Pressing the
Start/Pause button
program at the beginning.
The Start/Pause button
resume the program. The progress lights will
change to show the current status and the
Start/Pause light will stop flashing and turn green.
Changing the Programs knob will select a new
program and the Start/Pause light will flash
green. You can use this to select the Air Fluff
program to cool the clothes, if you find
them dry enough. Press the Start/Pause button
to begin a new program.
Note
)
must
will re-start a new
must be pressed to
9
EN