The Controls; Start And Programmes - Ariston ASL70C Instruction Booklet

19504265000 English.

Start and Programmes

The Controls

•
Programmes knob
! Warning, if after pressing the start button the
programme knob position is changed, the new position
will NOT change the programme selected.
! Position 0, turning the knob to position 0 resets and
cancels a programme.
•
Option Buttons/ Lights
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected on the Programmes knob before an
option can be selected. Not all options are available for
all programmes (see Start and Programmes). If an option
is not available and you press the button, the buzzer will
beep four times. If the option is available there will be
one beep and the option light next to the button lights to
confirm the selection.
•
Progress ( Drying,
Creasecare) / Delay (3hr 6hr 9hr 12hr) Lights
When the light next to the delay button is on, these
lights flash to indicate the delay time selected. During
other programmes they indicate the progress of the
dryer each one comes on as the corresponding phase
starts.
•
Time Delay
The start of some programmes (see Start and
Programmes) can be delayed for up to 12 hours in 3hr
steps. Ensure the water bottle is emptied before setting a
delayed start.
When a delayed start is in progress the light next to the
delay button will be on and the selected delay period light
will flash (after the start button has been pressed).
To set a delayed start press the Time delay button and the
light next to the button will come on together with the 3hr
delay light. Pressing the button again will advance the
delay setting to 6hr, the 3hr light goes out and the 6hr light
is on. Each time you press the button the delay setting will
advance 3hrs as indicated by the corresponding light. If the
12hr light is on pressing the button again will cancel the
delay.
You can also cancel the delay by turning the Programmes
knob to 0, wait for the buzzer to beep and then turn back to
your selected programme.
•
Pre Creasecare
When a delayed start has been selected the clothes are
tumbled occasionally during the delayed period to help
prevent creases developing.
•
High Heat
When available this button selects high heat. Press this
button and a high heat setting is selected and the light
next to the button comes on. Timed programmes have
default to low heat. If the light next to the button is on
then pressing this button selects low heat setting and
the light goes out.
{PDF Created 13/11/04 11:53}
Cool tumble, Post
•
Alarm
Available on all programmes and allows the buzzer to
give a signal at the end of the drying cycle to remind
you that the clothes are ready to be removed.
Press the button and the light will show that the option is
selected.
•
Post Creasecare
The clothes are occasionally tumbled after end of the
drying and cool tumble cycles to help prevent creases
developing, should you not be available to remove the
load immediately the programme is complete
•
Empty Water Light / Container
(If you have plumbed your dryer to a drain this light can
be ignored, as there is no need to empty the water
container.)
When this light is on (not flashing) its reminds you to
empty the water container.
If the water container fills during a programme, the
heater turns off and the dryer does a period of Cool
Tumble then the light flashes and the buzzer sounds.
After this it stops and all 3 Progress lights and the 3hr
delay light come on and the empty water light flashes.
You must empty the container and restart the dryer or
the clothes will not dry. After re-starting the dryer the
light will take a few seconds to go out.
To avoid this always empty the water container each
time you use the dryer (see Maintenance).
•
Door Opening
Opening the door during a programme will stop the
dryer and have the following effects
•
All 3 Progress lights and the 3hr delay light
come on.
•
During a delay phase the delay will continue
to count down. The start button must be
pressed to resume the delay programme. One
of the delay lights will flash to show the
current delay setting.
•
The start button must be pressed to resume
the programme. The progress lights will
change to show the current status.
•
During the cool tumble or post creascare
phase of a drying program and anytime during
an Airing or Cool tumble programme, the
Programme will finish. Pressing the start
button will re-start a new programme at the
beginning.
•
Changing the Programmes knob will select a
new programme, after you press the start
button. You can use this to select the Cool
Tumble programme to cool the clothes if you
find them dry enough.
•
Note
If you have a power cut, switch off the power or
remove the plug, press the start button and the
programme will resume
6
TD4048EX Issue 3