Advertisement
iMPORTANT SAFETY iNSTRUCTiONS
Toreduce the riskof severeinjuryor death:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with the door controls. Keep the remote control away from children.
3. Always keep the moving door in sight and away from people and objects until the door is completely
closed. NO ONE SHOULD
CROSS THE PATH OF THE MOVING DOOR.
4. NEVER GO UNDER A STOPPED,
PARTIALLY OPEN DOOR.
5. Test operator monthly. The door MUST reverse on contact with a 11/2" high object (or a 2" x 4" board
laid flat) at the center of the doorway on the floor. After adjusting either the force or the limit of travel,
retest the door Opener. Failure to adjust the Opener properly may cause severe injury or death.
6. When possible,
use the emergency
release only when the door is closed. Use caution when using this
release with the door open. Weak or broken springs are capable of increasing the rate of door closure
and increasing
the risk of severe injury or death.
7. KEEP DOORS PROPERLY BALANCED.
See Owner's Manual. An improperly
balanced door increases
the risk of severe injury or death. Have a qualified
service person make repairs to cables, spring
assemblies,
and other hardware.
8SAVE THESE ! STRUCTIONS.
4.
Safe-T-Beam® System.
• Use Self-Diagnostic
STB system Troubleshooting
information to maintain safe operation (Below).
.
Door springs
and hardware.
• Do not operate garage door automatically
or
manually
if springs are broken.
- CONTACT A PROFESSIONAL
FOR SERVICE.
2. Door balance.
• Close the door.
• Pull emergency release knob down to release
door from carriage assembly.
• Raise door manually approximately
3 feet.
- Door should stay in that position or close
very slowly.
- If door moves quickly, HAVE DOOR SERVICED
BY A PROFESSIONAL.
• Close the door.
• Pull emergency release knob toward power
head to place release lever in engaged position.
- Operate door using remote.
- Door will re-attach itself to carriage assembly.
3. Contact reverse.
• Place a 2"x 4" board laid flat on floor.
- In center of garage door opening.
• Close door by using wall button or
remote control.
- Door fails to reverse on contact with board see
Section 7 "CONTACT REVERSE."
- Operator still fails CONTACT A
SERVICE PROFESSIONAL.
Use This Guide To Correct Problems With Door Operator.
If These Solutions Do Not Work,
Call Customer Service at 1.800.35.GENIE
SOURCE
SENSOR
INDICATED
REQUIRED
RED LED
GREEN LED
CONDITION
ACTION
0
ON
O
ON
NORMAL OPERATION
NONE REQUIRED
O
OFF
O
OFF
1POWER HEAD NOT
1CHECK BREAKERS,
POWERED
FUSES, PLUGS
2 WIRING FROM
2 CHECK WIRING FOR
POWER HEAD BAD
OBVIOUS SHORTS
O
OFF
_
ON
IWIRINGTO
1CHECKWIRING
SOURCE MISSING
OR BAD
2 REMOVE POWER
2 POWER HAS BEEN
AND RRAPPLY
INTERRUPTED
tO
0
_
ON
1 BEAM NOT ALIGNED
1 CHECKALIGNMENT
2 BEAM OBSTRUCTED
2 CHECK FOR
2 BLINKS, PAUSE
OBSTRUCTION
(REPEAT)
3 SENSORDEFECTIVE
3 CALLCUST SERV
O_O
O
OFF
I WIRE TO SENSOR
I CHECK WIRING
MISSING OR BAD
2 BLINKS,PAUSE
2 SENSOR DEFECTIVE
2 CALL CUST SERV
(REPEAT)
_O
O
ON
I SENSOR RECEIVING
IATTEMPTTO
INTERFERENCE
DETERMINE SOURCE
3 BLINKS, PAUSE
OF INTERFERENCE
(REPEAT)
2 CALL CUST SERV
OOOOO
l_
ON
ISOURCENOT
ICALLCUSTSERV
SENDINGPULSES
4 BLINKS, PAUSE
2 SOURCE DEFECTIVE
2 CALL CUST SERV
(REPEAT)
NOTE: IF OPERATING
PROBLEM
EXISTS, THE DOOR CAN BE CLOSED
iF YOU:
• DISCONNECT
THE STB SYSTEM
FROM THE OPERATOR
• HOLD WALL CONTROL
BUTTON
DOWN UNTIL DOOR IS CLOSED
REMOTE
CONTROL
& WIRELESS
KEYPAD WILL NOT WORK WITHOUT
STB)
For Answers:
CALL CUSTOMER
SERVICE at 1.800.35.GENIE
Advertisement
