Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

 

Summary of Contents

  • Page 2

    How to discard a used battery Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery before disposal to prevent fire, heat generation caused by short circuit.

  • Page 3

    NOTICE A warning label is attached to the equipment. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer about replacement. WARNING Name: To avoid electrical shock, do not Warning Label (1) remove cover.

  • Page 4

    The installer of the equipment is solely responsible for the proper installation of the equipment. FURUNO will assume no responsibility for any damage associated with improper installation. Use the specified power cable.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS FOREWORD ... v SYSTEM CONFIGURATION ... vi EQUIPMENT LISTS... vii 1. OPERATION ... 1 1.1 Control Description... 1 1.2 Power On/Off ... 2 1.3 Adjusting Display Contrast and Brilliance... 2 1.4 Choosing a Display Mode ... 2 1.5 Choosing Range ...

  • Page 6

    We are confident you will see why the FURUNO name has become synonymous with quality and reliability. For over 60 years FURUNO Electric Com- pany has enjoyed an enviable reputation for innovative and dependable marine elec- tronics equipment. This dedication to excel- lence is furthered by our extensive global network of agents and dealers.

  • Page 7

    SYSTEM CONFIGURATION FCV-620 DISPLAY UNIT CV-620 Transducer 520-5PSD, 520-5MSD, 525-5PWD, 525ST-MSD, 525ST-PWD FCV-585 DISPLAY UNIT CV-585 Matching Box MB-1100* Transducer 520-5PSD, 520-5MSD, 525-5PWD, 525ST-MSD, 525ST-PWD Power supply 12-24 VDC GPS Navigator Water temperature sensor Water temperature/speed sensor ST-02MSB, ST-02PSB Water temperature sensor...

  • Page 8

    • Filter cleaner (1 pc., 02-155-1082-1, 100-332-651-10) Spare Parts Fuse (2 pcs., FGBO-A 125V 2A, 000-155-849-10) (SP02-05001) Template C22-00502 Operator’s Guide MLG-23740 Operator’s Manual OME-23740 Standard supply for FCV-585 Name Display Unit CV-585 520-5PSD Transducer 520-5MSD 525-5PWD Triducer (transducer 525ST-MSD...

  • Page 9

    EQUIPMENT LISTS Name Installation Materials • Cable assy. (1 pc., KON-004-02M, 000-156-405, for power and data) (CP02-07900) • Self-tapping screw (4 pcs., 5x25 SUS304, 000-162-610-10) • Flush mounting sponge (1 pc., 02-155-1081-1, 100-330-851-10) • Wing nut (4 pcs., M4 SUS304, 000-863-331) •...

  • Page 10: Operation, Control Description

    OPERATION Control Description Note: The FCV-620 and FCV-585 share the same features. For sake of brevity, this manual uses “FCV-620”. Control • Opens/closes menu. MENU/ESC • Escapes from current operation. • Moves cursor on the menu. • Adjusts settings. (TrackPad) •...

  • Page 11: Power On/off, Adjusting Display Contrast And Brilliance, Choosing A Display Mode

    When this occurs, press the MENU/ESC key twice to close the menu. Installation menu 1. Press the show the contrast/brilliance adjustment win- dow. (The FCV-585 does not have the con- trast function.) Contrast/brilliance adjustment window 2. To adjust brilliance, press the Continual pressing changes the brilliance continuously (0 →...

  • Page 12

    2. Rotate the MODE knob again to choose the display mode desired. The screen you chose appears soon there- after. Single frequency display Low frequency (50 kHz) The sounder uses ultrasonic signals to detect bottom conditions. The lower the frequency of the signal, the wider the detection area.

  • Page 13

    1. OPERATION Bottom zoom display This mode expands bottom and bottom fish on the left-half window. This mode is useful for determining bottom contour. When the bottom depth increases, the display automatically shifts to keep the bottom echo at the lower part of the screen.

  • Page 14: Choosing Range, Adjusting Gain

    Choosing Range The basic range may be chosen in Auto or Manual mode. 1. Press the RANGE key to open the range set- ting window. Range Auto Manual 15 ft 30 ft 60 ft These are 120 ft available with 200 ft Manual mode.

  • Page 15: Measuring Depth, Menu Operating Procedure

    Sounder Display Alarm Data System Menu window Menu item window *: FCV-585 only 2. Use menu desired. The cursor (yellow) shows current selection. The items in the right window change with menu selected. 3. Press the ENTER key. The cursor (yellow) shifts to the menu item...

  • Page 16: Shifting Range

    the menu window (left) is displayed to gray. You may also use to move the cursor. 4. Use to choose the menu item desired and press the ENTER key. The selected setting box or window appears. Depth Size Small Medium Large [ENTER] : Set [MENU] : Cancel...

  • Page 17: Choosing Picture Advance Speed, Suppressing Interference

    1.11 Suppressing Interference Interference from other acoustic equipment operating nearby or other electronic equipment on your boat may show itself on the display as *: FCV-585 shown in the figure below. Follow the procedure only below to suppress interference. Interference from other sounder Pic.

  • Page 18: Suppressing Low Level Noise, Erasing Weak Echoes

    1. Press the MENU/ESC key to open the menu. 2. Use to choose Sounder and press the ENTER key. 3. Use to choose Interference and press the ENTER key. Interference Medium High Auto : Select [ENTER] : Set [MENU] : Cancel Interference setting window 4.

  • Page 19: A-scope Display

    1. OPERATION Color Erase [ENTER] : Set [MENU] : Cancel Color Erase setting window 4. Use to choose the color to erase and press the ENTER key. The setting range is 0 to 50 % in intervals of five. The larger the set- ting value, the greater the degree of erasion.

  • Page 20: Fish Information

    1.15 Fish Information You can turn the fish symbol indication (Solid or Striped) on or off. Also, you can show or hide the fish size and the depth value. For details about the Fish Symbols, see the information which follows the procedures in this section. Note: The fish size found by this sounder is intended for reference purposes;...

  • Page 21: Alarms

    1. OPERATION • When Fish Symbols or Fish Info are enabled, 50 kHz and 200 kHz beams are transmitted alternately even if a single fre- quency mode is in use. • Fish within the zero line area are not mea- sured.

  • Page 22: Func Key, Waypoints

    From (0∼2500ft) [ENTER] : Set [MENU] : Cancel Depth setting window (0.0∼99.0kt) (20.0∼110.0°F) Temperature Speed Temperature, Speed setting box 7. Use to set starting depth, tempera- ture or speed as appropriate and press the ENTER key. For Bottom and Fish (Normal), the starting depth is the range from the trans- ducer, and for Fish (B/L), from the bottom.

  • Page 23

    [ENTER] : Enter [MENU] : Quit Waypoint setting window Note1: When TLL or FURUNO-TLL is selected at TLL Output on the NMEA menu of the System menu, the latitude and longitude position at the cursor position is output to the navigator.

  • Page 24: Setting Up Nav Data Displays

    3. Use to choose WPT List and press the ENTER key. WPT List : Select [ENTER] : Enter [MENU] : Quit WPT List window 4. Use to choose an empty waypoint and press the ENTER key. The Waypoint setting window appears. Lat and Lon indicate the current position.

  • Page 25

    1. OPERATION Two-data Three-data display display Items displayable in (1) - (3): speed (STW)*, wind speed and direction*, destination waypoint data*, compass*, heading*, depth, position, course, range and bearing, trip meter, odometer, water temperature, air pressure, time-to-go to destination waypoint, XTE*, speed (SOG)* Items displayable in (4) - (9): depth, position, speed (SOG), speed (STW), course, range and bearing, trip meter, odometer,...

  • Page 26: Menu Items

    White Marker: Displays the chosen echo color in white. 1. Choose White Marker in the Sounder menu and press the ENTER key. White Marker *: FCV-585 only (see section 4.10.) [ENTER] : Set [MENU] : Cancel White Marker setting window 2.

  • Page 27

    1. OPERATION against short range echoes. Note that this func- tion is operative when manual is selected on the GAIN knob. Smoothing: Smoothes echo presentation when enabled. Adjust the setting when echoes appear “spotty”. TX Power: Interference may appear on the screen when an echo sounder having the same frequency as your own is being operated in the vicinity of your vessel.

  • Page 28

    Colors: Choose the number of colors to use: 8, 16 or 64. Header Info: Turn the data area indication (appears at the top on the screen) on or off. G:AF R:A 50/200 Data area Data menu This menu mainly sets up how to display data input by external equipment.

  • Page 29: System Menu, Displaying System Sub Menu, Range Menu, Key Menu, Lang Menu

    SYSTEM MENU Displaying System Sub Menu The System menu mainly consists of items which once set do not require frequent adjust- ment. This menu has nine sub menus. To dis- play each sub menu, do the followings. 1. Press the MENU/ESC key to open the menu.

  • Page 30: Units Menu, Calib Menu

    Japanese. To change language, select lan- guage desired and press the ENTER key. Units Menu Units Depth : ft : °F Temp Fish Size : inch Speed : kt Wind : kt Distance : nm : Select [ENTER] : Enter [MENU] : Back Units menu...

  • Page 31: Demo Menu

    2. SYSTEM MENU Demo Menu Demonstrate Demonstrate : Off : Select [ENTER] : Enter [MENU] : Back Demo menu Demonstrate: The demonstration mode pro- vides, without connection of the transducer, simulated operation of the equipment, using internally generated echoes. All controls are operative.

  • Page 32: Maintenance, Trouble Shooting, Maintenance, Cleaning The Display Unit, Transducer Maintenance, Replacing The Fuse

    MAINTENANCE, TROUBLE- SHOOTING WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. IMPORTANT Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors.

  • Page 33: Troubleshooting, Diagnostics

    Push [MENU] 3 times to exit. *: Updated every second. XX: Program version number **: FCV-620: 0252346-XX.XX FCV-585: 0252347-XX.XX Test display The ROM, SDRAM and NMEA port are checked, with the results shown as OK or NG (No Good). For any NG, request ser- vice.

  • Page 34: Test Pattern, Memory Clear

    Checking GAIN knob: Rotate the knob. The indication goes higher with clockwise rotation; lower with counterclockwise rota- tion. Press the knob. The knob corre- sponding on-screen circle "lights" in red if the knob is normal. Checking MODE knob: Rotate the knob, and corresponding on-screen circle "lights"...

  • Page 35: Installation, Display Unit

    Observe the following compass safe dis- tances to prevent disturbance to the mag- netic compass: Standard compass FCV-620: 0.3 m, FCV-585: 0.5 m Steering compass FCV-620: 0.3 m, FCV-585: 0.3 m Tabletop mounting 1. Remove the tape from the bottom of the bracket assembly.

  • Page 36: Thru-hull Mount Transducer

    Thru-hull Mount Transducer Transducer mounting location The thru-hull mount transducer (520-5PSD, 520-5MSD) provides the best performance of all, since the transducer protrudes from the hull and the effect of air bubbles and turbu- lence near the hull skin is reduced. When the boat has a keel, the transducer should be at least 30 cm away from it.

  • Page 37

    4. INSTALLATION Typical thru-hull mount transducer installations Flat Washer Fairing Block Hull Deep-V Hull Flat Washer Hull Rubber Washer Flat Hull Typical thru-hull mount transducer installations Procedure for installing the thru-hull mount transducer 1. With the boat hauled out of the water, mark the location chosen for mounting the trans- ducer on the bottom of the hull.

  • Page 38: Transom Mount Transducer, Inside-hull Transducer

    Transom Mount Transducer The transom mount transducer is very com- monly employed, usually on relatively small I/ O or outboard boats. Do not use this method on an inboard motor boat because turbulence is created by the propeller ahead of the trans- ducer.

  • Page 39

    4. INSTALLATION Remarks on installation • Turn off the engine and anchor the boat while installing the equipment. • Install the transducer in the engine room. • Except for installing the transducer to the bottom of hull, do not turn on its power so it may be damaged.

  • Page 40: Triducer

    b)Gently dismount the transducer with a knife or a piece of wood. c)Reattach the transducer elsewhere as shown in "Attaching the transducer." d)Check the installation again. Final preparation Support the transducer with a piece of wood to keep it in place while it is drying. Let the transducer dry 24-72 hours.

  • Page 41

    4. INSTALLATION Note 3: For single drive boat, mount on the starboard side at least 75 mm (3") beyond the swing radius of the propeller. 75 mm (3") minimum beyond swing radius Mounting location on single drive boat Note 4: For twin drive boat, mount between the drives.

  • Page 42

    3. If the bracket has been temporarily fas- tened to the transom, remove it. Apply a marine sealant to the threads of the three #10 x 1-1/4" self tapping screws to prevent water seeping into the transom. Screw the bracket to the hull. Do not tighten the screws completely at this time.

  • Page 43: Optional Water Temperature/speed Sensor, Optional Water Temperature Sensor

    4. INSTALLATION 8. Position the two cable clamps and fasten them in place. If used, push the cable cover over the cable and screw it in place. 9. Route the cable to the instrument being careful not to tear the cable jacket when passing it though the bulkhead(s) and other parts of the boat.

  • Page 44: Wiring

    Thru-hull mount water temperature sensor T-02MSB, T-03MSB • Select a suitable mounting location consid- ering the following points: • Select a mid boat flat position. The sensor does not have to be installed perfectly per- pendicular; however, the location should not be such that the transducer may be damaged when the boat is dry-docked.

  • Page 45

    4. INSTALLATION Fuse holder Power supply lines (red and black) Cable tie How to fix fuse holders Establishing the ground The ground wire (1.25 sq or more, local supply) should be as short as possible. The signal line ground is isolated from the chassis ground, however the power line is not insu- lated.

  • Page 46: Iec 61162-1 Data Sentences

    Matching box MB-1100 Part Type Code No. Matching MB-1100 000-041-000 Box* Crimp-on FV1.25-3, 000-538-113 Cord Lock** NC-1 000-516-650 *: With 10P connector cable **: For connecting two transducers Fabricating the transducer cable Fabricate the transducer cable as below and connect it to the matching box. Vinyl Sheath Shield Taping...

  • Page 47: Adjustments After Installation

    To display this information on the Port 2 screen when two sensors are connected, set NMEA Port on the NMEA menu to In/In. Transducer (FCV-585 only) Choose transducer type among 600 W, 1 kW and 50/200-1T on the Sounder menu. 600W...

  • Page 48: Menu Tree

    Speed ( Off , Inside, Outside) From (0.0 - 99.0 kt, 0.0 kt ) Span (1.0 - 50.0 kt, 1.0 kt ) Arrival ( Off , Inside, Outside) Radius (0.01 - 99.99 nm, 0.01 nm ) Bold: Default *: FCV-585 only...

  • Page 49

    NMEA Port ( In/Out , In/In) NMEA Output ( Off , On) WAAS Setup ( Off , WAAS-00 - WAAS-27) TLL Output (Off, TLL , FURUNO-TLL) Port Monitor Draft (-15.0 - +50.0 ft, +0.0 ft ) Gain ADJ 200 (-20 - +20, +0 ) Gain ADJ 50 (-20 - +20, +0 ) Temp (-20.0 - +20.0 °F, +0.0 °...

  • Page 50: Specifications

    SPECIFICATIONS OF ECHO SOUNDER GENERAL TX Frequency Transmit Method Output Power FCV-620 FCV-585 TX Rate Pulse-length Sensitivity DISPLAY UNIT Display System FCV-620 FCV-585 Display Mode Expansion Mode Basic Range Unit Range Shift Zoom Range Display Advance Speed 8 steps (Lines/TX; 4/1, 2/1, 1/1, 1/2, 1/4, 1/8, 1/16, Freeze)

  • Page 51

    3. INTERFACE Input Data Sentences Output Data Sentences IEC61162-1 (NMEA0183 Ver 1.5/2.0/3.0), interval: 2 s 4. POWER SUPPLY FCV-620 FCV-585 5. ENVIRONMENTAL CONDITION Ambient Temperature Relative Humidity Waterproofing and Dust Proofing (IEC60529) Vibration 6. CHASSIS COLOR Display Unit IEC61162-1 (NMEA0183 Ver 1.5/2.0/3.0) Order of priority Latitude/Longitude: GGA>RMC>RMA>GLL...

  • Page 52

    28/May/2010 Y.NISHIYAMA 西山 義浩 電子署名者 :西山 義浩 DN : cn=西山 義浩, o, ou=情技課, email=yoshihiro.nishiyama@furuno.co.jp, c=JP - 日本 日付 : 2010.05.28 19:43:18 +09'00' Y.NISHIYAMA 28/May/2010...

  • Page 53

    Y.NISHIYAMA 2/Apr/2010 西山 義浩 電子署名者 :西山 義浩 DN : cn=西山 義浩, o, ou=情技課, email=yoshihiro.nishiyama@furuno.co.jp, c=JP - 日本 日付 : 2010.04.02 19:17:56 +09'00' Y.NISHIYAMA 2/Apr/2010...

  • Page 55

    XDR-M XDR-SHIELD XDR-P TEMP0V MJ-A10SRMD TEMP SPD0V/ST-SHIELD 12V-P1 MJ-A10SPF 02S4147,0.2m MJ-A6SRMD XDR-M XDR-SHIELD XDR-P 8m,φ5.4 TEMP0V TEMP SPD0V/ST-SHIELD 12V-P1 10m,φ5.4 MJ-A10SPF XDR-M XDR-SHIELD XDR-P MJ-A10SPF アカ クロ アカ クロ アカ ミドリ アオ クロ...

  • Page 57

    (title and/or number and date of issue of the standard(s) or other normative document(s)) For assessment, see • EMC Test Report FLI 12-05-053 of 14 November 2005 prepared by Furuno Labotech International Co., Ltd. This declaration is issued according to the Council Directive of 3 May 1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility (89/336/EEC).

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: