Alert Standard Format; Dell Openmanage™ Applications; Dell Client Manager (Dcm) Console - Dell OptiPlex 760 Service Manual

Be formatted using the FAT16 file system with no system files
l
Contain only the setup.bin file
l
NOTE: The key should not be bootable.
To provision AMT using a USB key, plug the USB key into a USB port prior to boot. During POST, the BIOS displays a message stating that the computer is being
provisioned.

Alert Standard Format

Alert Standard Format (ASF) is a DMTF management standard that specifies "pre-operating system" or "operating system-absent" alerting techniques. The
standard is designed to generate an alert on potential security and fault conditions when the operating system is in a sleep mode or the computer is turned
off. ASF is designed to supersede previous operating-system-absent alerting technologies.
Your computer supports the following ASF version 1.03 and 2.0 alerts and remote capabilities:
Alert
Chassis: Chassis Intrusion – Physical Security
Violation/Chassis Intrusion – Physical Security Violation
Event Cleared
CPU: Emergency Shutdown Event
Cooling Device: Generic Critical Fan Failure/Generic Critical
Fan Failure Cleared
Temperature: Generic Critical Temperature Problem/Generic
Critical Temperature Problem Cleared
Battery Low
ASF allows Remote Management and Control Protocol (RMCP) messages to be exchanged between a remote management console and a client computer that
is in a "pre-operating system" or "operating system-absent" state. RMCP messages can be sent to instruct a client computer to start up, shut down, or
restart.
For more information about Dell's ASF implementation, see the ASF User's Guide and the ASF Administrator's Guide, which are available on the Dell Support
website at support.dell.com.
Dell OpenManage™ Applications
NOTE: Either Dell OpenManage™ applications and Dell™ Client Manager (DCM) are available for your computer to help meet your system management
needs. See Dell Client Manager (DCM)
You can manage your computer via IT Assistant and Dell OpenManage Client Instrumentation (OMCI).
IT Assistant configures, manages, and monitors computers and other devices on a corporate network. IT Assistant manages assets, configurations, events
(alerts), and security for computers equipped with industry-standard management software. It supports instrumentation that conforms to SNMP and CIM
industry standards.
For information on IT Assistant, see the Dell OpenManage IT Assistant User's Guide available on the Dell Support website at support.dell.com.
Dell OpenManage Client Instrumentation is software that enables remote management programs such as IT Assistant to do the following:
Access information about your computer, such as how many processors it has and what operating system it is running.
l
Monitor the status of your computer, such as listening for thermal alerts from temperature probes or hard drive failure alerts from storage devices.
l
A computer that has Dell OpenManage Client Instrumentation set up on a network that uses IT Assistant is a managed computer. For information about Dell
OpenManage Client Instrumentation, see the Dell OpenManage Client Instrumentation User's Guide available on the Dell Support website at support.dell.com.
Dell Client Manager (DCM)
NOTE: Either Dell™ Client Manager (DCM) or Dell OpenManage™ applications are available for your computer to help meet your system management
needs. See Dell OpenManage™ Applications

Dell Client Manager (DCM) Console

The Dell Client Manager (DCM) console allows you to configure, manage, and monitor Dell computers on a corporate network via a simple GUI interface.
Through the DCM console you can manage assets, configurations, events (alerts), status, and security for computers equipped with industry-standard
management software. For information about standards supported by DCM, see www.altiris.com.
For information about the DCM console, see www.altiris.com or the Dell Support website at support.dell.com.
The DCM console also allows you to:
Description
The computer chassis with the chassis intrusion feature (optional on some
computers) installed and enabled has been opened or the chassis intrusion alert has
been cleared.
The processor temperature is too hot and the power supply has shut down.
The fan speed (rpm) is out of limits or the fan speed (rpm) problem has been
resolved.
The computer temperature is out of limits or the computer temperature problem has
been resolved.
The computer battery has reached a voltage of 2.2 V or lower.
for information about DCM.
for information about Dell OpenManage products.