Table of Contents
Advertisement
ED12-011A
Adjusting the Air Flow Direction
You can adjust the air flow direction to increase your
comfort.
Adjusting the
horizontal blade (flap)
Press
.
SWING
l
Every time the button is pressed, "
" appears or disappears.
.......
The flap automatically
swings up and down.
ON
.......
To stop the flap at an
angle you like, press
ON
Notes on flap angles
l
When
SWING
is selected, the flap swinging range depends
on the operation mode. (See the figure.)
l
The real flap angles are differ from the display of remote
controller.
In DRY mode or COOL mode
When stop operation
0˚
Upper limit in cooling
25˚
Lower limit in cooling
In HEAT or FAN mode
When stop operation
20˚
Upper limit in heating
45˚
Lower limit in heating
ATTENTION
l
Always use a remote controller to adjust the flap angle. If
you attempt to move it forcibly with hand when it is
swinging, the mechanism may be broken.
10
Good Sleep Cooling Operation
(G-SLEEP)
The "Good Sleep Cooling Operation" makes the 1/f Fluctuating Temperature.
It brings you comfortable sleep as it prevents from getting chilied.
-SLEEP
1
Press
in cooling operation.
n
To change the temperature setting.
n
To change the air flow rate setting.
n
To change the air flow direction setting.
n
To cancel the "Good Sleep Cooling Operation ", press
Back to the normal cooling opration.
Notes on "Good sleep cooling operation "
l
We adopt the 1/f fluctuation rhythm in temperature control.
A 1/f fluctuation rhythm is used in temperature control. With it, temperature is fluctuated within a ±1˚C
range of the set temperature.
The 1/f fluctuation is comfortable rhythm existed in the natural world. (refer to "What's the 1/f
fluctuation")
l
Air blow is the lowest when the fan is set to "AUTO".
l
If you don't like this function, change the operation mode. (See page 8)
What is 1/f fluctuation...
It seems irregular but there seems to be a self-resemblance rule in our mother nature.
For example, the waves in the ocean forms irregularly but when you look at the coast line, there are
some places where they look similar.
When you look close around you, our heart doesn't beat in regular intervals but shows "1/f
fluctuation" in a long term. The research shows this "1/f fluctuation" and comfort has some kind of
relation and is applied to the comfort control fiels.
12
Room Air Conditioners SUPER MULTI H-Series
Adjusting the louvre
Hold the knob and move the louvre.
(You will find a knob on the left-side and the right-side
blades.)
ATTENTION
SWING
.
l
Be careful when adjusting the louvre. Inside the air
outlet, a fan is rotating at a high speed.
(See page 8.)
(See page 8.)
(See page 10.)
-SLEEP
.
Timer Operation
Timer functions are useful for automatically switching the
air conditioner on or off at night or in the morning. You can
also use OFF TIMER and ON TIMER in combination.
OFF TIMER operation
l
Chec k that the clock is correct.
If not, set the clock to the present time. (See page 7.)
1
Press
OFF
while the air conditioner
is operating.
is displayed.
AM
AM
blinks.
* Previous time setting
appears on display.
2
Press
until the time setting
TIMER
reaches the point you like.
l
Every pressing of either button increases or decreases
the time setting by 10 minutes. Holding down either
button changes the setting rapidly.
3
Press
OFF
once again.
ON
AM
OFF
Then the TIMER lamp lights up.
n
To cancel the timer:
Press
.
CANCEL
Then the TIMER lamp goes off.
Notes on OFF TIMER
l
NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically
adjusts the temperature setting (0.5ºC up in COOL, 2.0˚C down
in HEAT) to prevent excessive cooling (heating) for your
pleasant sleep.
Intelligent Eye
"Intelligent Eye" is the infrared sensor which detecs the
human movement.
SENSOR
1
Press
While the air conditioner
is operating. (The Sensor lamp lights up.)
n
To cancel the "Intelligent Eye",
SENSOR
press
. (The Sensor lamp goes off.)
[EX.]
When somebody in the room
Normal operation
(The sensor lamp lights up.)
When nobody in the room
20 min. after, start save operation.*
(The sensor lamp goes off.)
Sombody back in the room
Back to normal operation.
(The sensor lamp lights up again.)
"Intelligent Eye" is useful for
Energy Saving
* Save operation
l
Change the temperature –2˚C in heat/ +2˚C in cool/ +1˚C in
dry mode from set temperature.
l
Decrease the air flow rate slightly in fan operation.
Notes on "Intelligent Eye"
l
Application range is as follows.
Vertical angle 40˚
Horizontal angle 50˚
(Side View)
(Top View)
50˚ 50˚
80˚
l
Sensor may not respond when you are 5m or
more away. (Check the application range)
l
Sensor detection sensitivity changes according
to indoor unit location, the speed of passersby,
temperature range, etc.
l
The sensor also mistakenly detects pets,
sunlight, fluttering curtains and light reflected
off of mirrors as passersby.
Operation Manual
ON TIMER operation
l
Check that the clock is correct. If not, set the clock to the present
time (See page 7).
1
Press
ON
while the air conditioner is
not operating.
is displayed.
AM
AM
blinks.
* Previous time setting
appears on display.
2
Press
until the time setting
TIMER
reaches the point you like.
l
Every pressing of either button increases or decreases
the time setting by 10 minutes. Holding down either
button changes the setting rapidly.
3
Press
once again.
ON
ON
OFF
AM
Then the TIMER lamp lights up.
n
To cancel the timer:
Press
CANCEL
.
Then the TIMER lamp goes off.
Combining ON TIMER and OFF TIMER
l
A sample setting for combining the two timers is shown below.
(Example)
Present time: 11:00 PM
(The unit operating)
OFF TIMER at 0:00 a.m.
Combined
ON TIMER at 7:00 a.m.
AM
AM
Notes on ON,OFF TIMER
l
When TIMER is set, the present time is not displayed.
l
Once you set ON,OFF TIMER, the time setting is kept in the
memory. (The memory is canceled when remote controller
batteries are replaced.)
ATTENTION
n
In the following cases, set the timer again.
l
After a breaker has turned OFF.
l
After a power failure.
l
After replacing batteries in the remote controller.
11
n
Adjusting the angle of the
Intelligent-eye sensor
You can adjust the angle of the Intelligent-eye
sensor to remove the detection area.
(Adjustable angle: 15˚ to right and left of
centre)
Intelligent-eye
15˚
15˚
sensor
Gently push and slide the sensor to adjust
the angle.
Moving the sensor to the left
Moving the sensor to the right
After adjusting the angle, gently wipe the
sensor with a clean cloth, being careful not to
scratch the sensor.
CAUTION
Do not hit or violently push the Intelligent-eye sensor. This
can lead to damage and malfunction.
l
Saving operation will not go on during
powerful operation.
l
Night set mode (see page 11.) will not go on
during you use Intelligent Eye.
l
You can sleep more comfortablly by using
"Good Sleep Cooling Operation (G-SLEEP)"
function (see page 12.) at the same time.
CAUTION
Do not place large objects near the sensor.
Also keep heating units or humidifiers outside
the sensor's detection area.
This sensor can detect objects it shouldn't as
well as not detect objects it should.
13
97
Advertisement
Table of Contents
