Location Requirements - Maytag MVWB880BW Instructions Manual

To order, please refer to the phone number or website on the
back page of your "Use and Care Guide."
8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)
■
8212641RP 5 ft. (1.5 m) Inlet hose, Black EPDM (2 pack)
■
8212646RP 4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)
■
8212545RP 5 ft. (1.5 m) Inlet hose, Red and Blue EPDM
■
(2 pack)
8212487RP 5 ft. (1.5 m) Nylon braided inlet hose (2 pack)
■
8212638RP 6 ft. (1.8 m) Nylon braided inlet hose, space
■
saving 90° elbow, hypro-blue steel couplings
(2 pack)
8212637RP 6 ft. (1.8 m) Inlet hose, Black EPDM, space
■
saving 90° elbow, hypro-blue steel couplings
(2 pack)
Alternate parts
(Not supplied with washer)
Your installation may require additional parts. To order, please
refer to the phone number or website on the back page of your
"Use and Care Guide."
If you have: You will need:
Laundry tub or Sump pump system (if not already
standpipe taller available)
than 96" (2.4 m)
1" (25 mm) 2" (50 mm) diameter to 1" (25 mm)
diameter standpipe diameter Standpipe Adapter Kit,
Part Number 3363920 and
Connector Kit, Part Number 285835
Overhead sewer Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump
pump, and connectors (available
from local plumbing suppliers)
Floor drain Siphon Break Kit,
Part Number 285834
Extension Drain Hose,
Part Number 285863
Connector Kit, Part Number 285835
Drain hose too short Extension Drain Hose,
Part Number 285863
Connector Kit, Part Number 285835
Lint clogged drain Drain protector, Part Number 376031

LOCATION REQUIREMENTS

Select proper location for your washer to improve performance
and minimize noise and possible "washer walk." Install your
washer in a basement, laundry room, closet, or recessed area.
Proper installation is your responsibility.
You will need:
■
■
■
■
■
:
IMPORTANT: Do not operate, install, or store washer where
it will be exposed to water, weather, or at temperatures below
32° F (0° C). Some water can remain in washer and can cause
damage in low temperatures. See your "Use and Care Guide"
for information on winterizing.
Spacing for recessed area or closet installation
All dimensions show recommended spacing allowed, with tested
spacing of 0" (0 mm) clearance on sides.
■
■
■
■
■
17"*
(432 mm)
1"
(25 mm)
* Required spacing
A water heater set to deliver 120°F (49°C) water to the washer.
A grounded electrical outlet located within 4 ft. (1.2 m) of
where the power cord is attached to the back of the washer.
See "Electrical Requirements."
Hot and cold water faucets located within 3 ft. (900 mm)
of the hot and cold water fill valves, and water pressure
of 20–100 psi (138–690 kPa) for best performance.
Level floor with maximum slope of 1" (25 mm) under entire
washer. Installing the washer on carpet is not recommended.
A sturdy floor to support the washer weight (washer, water,
and load) of 315 lbs (143 kg).
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door, and
floor moldings.
Additional spacing should be considered on all sides of the
washer to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
27 / "
1 1" 1"
2
(699 mm)
(25 mm) (25 mm) (686 mm)
Front view
Side view
14"* max.
(356 mm)
48 in. *
2
(310 cm )
2
24 in. *
2
(155 cm )
2
27" 5"*
(127 mm)
Closet door
with vents
3"*
(76 mm)
3"*
(76 mm)
3