Dell 5330dn Workgroup Mono Laser Printer User Manual page 118

The rear door of output expander is not
Close Bin1 Door
securely latched.
The fuser door is not securely latched.
Close Fuser Door
The displayed tray is open.
Tray [x] Open
Tray [x] Open
Close Tray [x]
HCF(High Capcity Feeder) is open.
HCF Open
HCF Open
Close Door
There is no paper in the tray.
Tray [x] Empty
Load [Size][Type]
There is no paper in the HCF.
HCF Empty
Load [Size][Type]
There is no paper in the multi-purpose
MPF Empty
feeder.
Load [Size][Type]
Press Select
The paper size specified in the printer
Paper Mismatch/
properties does not match the paper
Tray [x]/MPF
being loading.
Load [Size][Type]
Continue ,
Cancel
Paper has jammed around the toner
Paper Jam 0
cartridge area.
Check Toner Cover
Paper has jammed in the feeding area of
MP Tray
the multi-purpose feeder.
Check MPF Door
Paper has jammed in the feeding area of
Paper Jam 0
the paper tray.
Check Tray[x]
Paper has jammed in the paper exit area
Paper Jam 1
or around the toner cartridge area.
Open/Close Door
Paper has jammed in the paper exit area. Clear the jam. See
Paper Jam 2...
Paper has jammed during duplex
Duplex jam 0...
printing.
Paper has jammed during duplex
Duplex jam 1...
printing.
The output tray is full.
Standard Bin Full/
Standard Bin is 90%
Full
The output tray of output expander is
Optional Bin1 Full
full.
There is a problem in the fuser unit.
Open Heat
Open Heat Error
Power Cycle
There is a problem in the fuser unit.
Low Heat/
Low heat Error
Power Cycle
There is a problem in the fuser unit.
Over Heat
Overheat Error
Power Cycle
A problem has occurred in the LSU(Laser
LSU Motor Error/
Scanning Unit).
LSU Motor Error/
Power Cycle
A problem has occurred in the LSU(Laser
Hsync Error/
Scanning Unit).
LSU Hsync Error
Power Cycle
There is a problem in the cooling fan of
Fuser Error
the printer.
Fuser Fan Locked
Power Cycle
There is a problem in the SMPS fan of the
SMPS Error
printer.
SMPS Fan Locked
Power Cycle
The fuser unit is not installed or not
Fuser Error/
detected.
Fuser Not Installed
Check Rear Door
There is a problem in your printer system. Unplug the power cord and plug it back
Inner Temp. Error/
Inner Temp. Error
Power Cycle
There is a problem in the development
Deve Motor Error/
motor of the printer.
Deve Motor Locked
Power Cycle
The printer is in power save mode.
Power Saver
Your printer is warming up now.
Warming Up
Close the door until it locks into place.
Open the rear door and close the fuser
door until it locks into place.
Close the tray until it locks into place.
Close the HCF until it locks into place.
Load paper in the tray. See "Loading
Print Media in the Paper Tray".
Load paper in the HCF. See "Using the
High Capacity Feeder".
Load paper in the multi-purpose feeder.
See "Using the Multi-purpose Feeder".
Load the correct paper in the tray.
Clear the jam. See "Around the toner
cartridge".
Clear the jam. See "Multi-purpose feeder
Jam".
Clear the jam. See "Paper Feed Jam (tray
1)" or "Paper Feed Jam (optional trays)".
Clear the jam. See "In the paper exit
area" or "Around the toner cartridge".
"In the paper exit
area" or "Around the toner cartridge".
Clear the jam. See "Duplex jam 0".
Clear the jam. See "Duplex jam 1".
The output tray can hold up to 250
sheets of plain paper. Once the paper is
removed from the output tray, the printer
resumes printing.
The output expander can hold up to 600
sheets of plain paper. Once the paper is
removed from the output expander, the
printer resumes printing.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Open and then close the rear door.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
Install the fuser unit or open and then
close the rear door.
in. If the problem persists, please call for
service.
Unplug the power cord and plug it back
in. If the problem persists, please call for
service.
When data is received, it switches to on-
line automatically.
Please wait a few minutes.