Table of Contents
Advertisement
6. SETTING AND ADJUSTMENTS BEFORE SHOOTING
6-9 Audio Input Level Adjustment
VF
ZEBRA
OFF
SKIN
AUTO
ON
AREA
WHITE
ACCU
FOCUS
VTR
AUDIO
TAKE
LEVEL CH-1
CH-1 audio input level control
For each audio channel, use the AUDIO SELECT switches to
select whether the audio input level adjustment should be set
to AUTO mode or MANUAL mode.
• When set to AUTO: Audio input level is fixed. In this mode,
the audio input level control does not
function.
• When set to MANUAL: Audio input level can be adjusted us-
ing the audio input level controls for
each audio input.
Adjusting the audio input level control of the front section
The audio input level control on the front section only af-
fects the CH-1 channel sound.
To use the audio input level control on the front section,
make the following settings.
• Set the CH-1 AUDIO SELECT switch to MANUAL.
• Set the VCR Setup Menu item No. 246 FRONT VOLUME
ENABLE to "ENABLE".
CAUTION:
The audio input level controls on the side section work
regardless of the setting of the VCR Setup Menu item No.
246 FRONT VOLUME ENABLE.
Manual Adjustment of Audio Input Level
The audio input level can be adjusted manually when the GY-
DV700W is in the record, record-pause or stop mode.
1.
Set the AUDIO SELECT switch of the channel whose audio
input level that you want to adjust manually to MANUAL.
2.
Rotate the audio input level control corresponding to the
audio input to be adjusted.
• Adjust so that the peak level does not exceed the -3dB
point when a loud sound is input.
• With microphone input, since the limiter circuit is activated,
the audio input level will not exceed 0 dB even if the
recording level control is turned up.
48
FILTER
1 3200k
ALARM
2 5600k+1/8ND
3 5600k
4 5600k+1/64ND
SHUTTER
STATUS
MONITOR
C
MENU
AUTO IRIS
FULL AUTO BLACK
LOLUX
BACK L
STRETCH
NORMAL
NORMAL
SPOT L
COMPRESS
NG
POWER
ON
OFF
CH-1 audio input level control
CH-1 Audio
select switch
OPERATE/WARNING
LIGHT
RESET
ON
OFF
MONITOR
COUNTER
SELECT
CTL
TC
UB
CH-1
AUDIO
CH-2
LEVEL
CH-2 audio input level control
How to use the audio input level control
on the front section
1 Set the audio input level control on the front section to
maximum (10) position.
2 Initially, adjust the input level using the CH1 audio input
level control on the side.
3 When a loud sound is input during recording, use the audio
input level control on the front section to lower the input
level.
Level meter
CH 1
40 30
CH 2
32k
48k
SP
AUD LOCK
WIDE
MENU
REMAIN
H
Viewfinder Status 1 Mode
F 5 . 6
STBY
Indicator level (reference)
–38
–32
CAUTION:
When the AUDIO INPUT LINE/MIC switch on the rear
section is set to MIC, be sure to check that the microphone
is connected to the AUDIO INPUT connector. If the
microphone is not connected, increasing the audio input
level could cause noise from the input connector to be re-
corded on the tape. When the microphone is not connect-
ed to the AUDIO INPUT connector on the rear panel, set
the LINE/MIC switch to LINE or turn down the audio input
level control.
CH-2 Audio
select switch
AUTO
MANUAL
AUDIO SELECT
AUDIO INPUT
CH-1
CH-2
AUDIO
CH-1
CH-2
FRONT
REAR
LEVEL
OVER
AUTO OFF DEW
20
10
0 dB
SERVO
RF
L i
OVER
SLAVE
PB
NDF
HOLD
H
M
S
F
E
BATT
F
REV FWD
M
ACCU - FOCUS
G
F
I
SD
B
CH1 - - - - + - -
CH2 - - - - + - -
M
0 9
9
< 6 0
1 .
2
4V
Audio leve
–26
–20
–14
–8 –2dB
Advertisement
Table of Contents
