Table of Contents
Advertisement
12-1 VCR Setup Menu (Cont'd)
Group
Upper row: Viewfinder display
Lower row: Counter display indication
SYSTEM
302: BACK SPACE
b-SP
307: LONG PAUSE
TIME
LGPt
396: BATTERY TYPE
bAtt
398: SSF MODE
SSF
399: REMOTE
FF/REW MODE
rEFF
TIME CODE
403: U-BIT SLAVE
UbSL
416: NON DROP/
DROP
tcG
ON
516: DISPLAY SELECT
SCREEN
diSP
Setting
Item
Value
STANDARD
QUICK
St
qU
3MIN
30MIN
03
30
12V
13.2V
14.4V
12
13
14
Note:
• If this setting is neglected, the unit's display of remaining of battery power and generation of
battery alarm will not work correctly.
• This setting is valid when battery pack is used. It is invalid when a DC power supply is used.
OFF
CUE MODE
MARK MODE
oF
cU
nr
FF/REW
SEARCH
FF
SH
TC&UB
TC
on
oF
DROP
NON DROP
dF
nF
TC
CLOCK
tc
cL
Contents
Selection of amount of back space for recording pause.
STANDARD : Normally use this setting.
QUICK
: Compared to STANDARD, the back space
becomes approximately 0.4 seconds shorter.
Use this setting when you want to start
shooting quickly. However, in the REGEN
mode, the time code may not continue.
To select the time (minutes) before the save mode (drum
head rotation stopped) is engaged when the record-pause,
still or stop condition continues.
3MIN
: 3 minutes
30MIN : 30 minutes
* When used in a cold environment, the setting will be 3
minutes regardless of the setting.
To be set in accordance with the used battery back type.
12V
: Choose this setting when using 12V battery
(12V DC Flat shape type).
13.2V
: Choose this setting when using 13.2V battery
(Anton-Bauer Trimpack 13, Propack 13, Magnum
13, Compack 13).
14.4V
: Choose this setting when using 14.4V battery
(Anton-Bauer Trimpack 14, Propack 14, Magnum
14, Compack 14).
Selection of the S.S.F. (Super Scene Finder) mode.
S.S.F. function:While recording, the time code data of a
desired recorded scene is stored in the unit's memory when
the TAKE button on the front section is pressed.
Settings cannot be changed during recording or SAVE mode.
OFF
: S.S.F. function is not available.
CUE MODE
: Selects the CUE mode.
When the TAKE button is pressed, the time
code data of the scene recorded at that
point is stored in the memory.
MARK MODE : Selects the MARK mode.
When the TAKE button is pressed the first time,
the time code of this point is stored as start
point of the scene. When the TAKE button is
pressed the second time, the time code of this
point is stored as ending point of the scene.
For details on the S.S.F. function, see page 60.
• When the VCR Setup Menu item No. 398 S.S.F. MODE is
set to CUE or MARK, the time code generator's running
method is internally set to the REGEN mode.
Specifies the operation when FF/REW signal is received from
the VTR remote connector during playback.
FF/REW
: FF/REW operation performed.
SEARCH : Search operation performed.
To set whether user's bits also should be slave-locked when
slave-locking with external time code generator.
TC&UB : User's bits also slave-locked
TC
: User's bits are not slave-locked
Selection of the time code generator's framing mode as either
drop or non-drop mode.
DROP
:The internal time code generator runs in drop mode.
Choose this setting when emphasizing the recorded time.
NON DROP:The internal time code generator runs in non
drop mode. Choose this setting when
emphasizing the frame number.
Selection of the appearance of the counter display when the
COUNTER switch is set to "TC" or "UB".
TC
: The time code is displayed.
CLOCK : The date/time is displayed.
12. SETUP MENU
Factory
Setting
STAND-
ARD
30MIN
12V
OFF
FF/
REW
TC
DROP
TC
69
Advertisement
Table of Contents
