Table of Contents
Advertisement
Troubleshooting
Troubleshooting
Possible causes
i The batteries have run out.
No power.
i The batteries are loaded backwards.
i The battery cover is not closed correctly.
i The AC power adapter plug has come
out of the power outlet.
i The camera has been left for a long period
with batteries and AC power adapter
removed.
Power cuts out during
The batteries have run out.
operation.
i Camera is being used in extremely cold
Batteries
run
out
quickly.
conditions.
i The terminals are soiled.
i The batteries can no longer be
recharged.
i The rechargeable batteries (if used)
have become deactivated, or the battery
capacity has diminished due to the
memory effect.
No photograph is taken
i No xD-Picture Card is inserted.
when pressing the
i The xD-Picture Card is full.
shutter button.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is
soiled.
i The xD-Picture Card is damaged.
i The Auto power off function has turned
the camera off.
i The batteries have run out.
Cannot use the flash.
i The shutter button was pressed while
the flash was charging.
i The flash is not popped up.
i The batteries have run out.
i The Mode dial is set to "
i Continuous shooting is selected.
The flash settings are
The Mode dial is set to "
/
M
<
restricted and cannot
, "
" , "
" , "
" or "
be selected.
The playback image is
i The subject is too far away.
dark even though the
flash was used.
i Your finger was covering the flash.
The image is blurred.
i The lens is dirty.
i You photographed scenery with Macro
mode selected.
i You took a close-up shot without
selecting Macro mode.
i You are shooting a subject that is not
suited to autofocusing.
There is speckling on
The picture was taken with a slow shutter
the image.
speed (long exposure) in a high-
temperature environment.
Cannot format the xD-
The xD-Picture Card contact area is
Picture Card.
soiled.
The camera does not
i The camera volume is set too low.
i The microphone was blocked during
emit any sound.
shooting/recording.
124
i There is something covering the speaker
during playback.
eIf you think the camera is faulty, check the following once more.
Solutions
i Load new or fully charged batteries.
i Load the batteries in the correct
direction.
i Close the battery cover correctly.
i Plug the adapter back in.
i Load the batteries or connect the AC power
adapter, and wait a short time before turning
the camera on.
Load new or fully charged batteries.
i Put the batteries in your pocket or
another warm place to heat them and
then load them into the camera just
before you take a picture.
i Wipe the battery terminals with a clean,
dry cloth.
i Load new or fully charged batteries.
i Use
the
rechargeable
discharging function to restore the
rechargeable batteries to full capacity.
i Insert an xD-Picture Card.
i Insert a new xD-Picture Card or erase
some unwanted frames.
i Format the xD-Picture Card on the
camera.
i Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Insert a new xD-Picture Card.
i Turn the camera on.
i Load new or fully charged batteries.
i Wait until the charging is completed
before pressing the shutter button.
i Pop up the flash.
i Load new or fully charged batteries.
À
i Change the Photography mode.
".
i Set continuous shooting to "OFF".
B
À
.
", "
", "
"
The flash settings are restricted because
>
".
the camera settings are tailored to the
scene
being
shot.
Photography mode for a wider range of
flash settings.
i Move to within the effective flash range
before taking the picture.
i Hold the camera correctly.
i Clean the lens.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock or " K " Manual focus
mode to take the picture.
This is a characteristic of CCDs and does
not indicate a camera fault.
Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Adjust the volume.
i Take care not to block the microphone
during shooting/recording.
i Make sure that the speaker is uncovered.
Troubleshooting
Frame erase does not
erase the frame.
The
ERASE
function does not erase
all the frames.
Screens
displayed in English.
There is no image or
sound on the TV.
battery
The TV image is black
and white.
When connecting the
camera to a PC, the
photographed image or
playback
appears
camera's LCD monitor.
Nothing happens when
using the Mode dial.
The camera no longer
works correctly.
Change
the
Cannot
PictBridge.
The
camera
connected to a PC
when the USB mode
was set to " ® ".
Possible causes
Some frames may be protected.
ALL
are
not
A language other than English is selected
in the " ô "
setting in the " ˜ "
SET-UP menu (➡P.92).
i The included A/V cable was connected
during movie playback.
i The camera is not connected to the TV
correctly.
i "TV" is selected as the TV input.
i The
"
õ
"
video output setting is incorrect.
i The TV volume is turned down.
The
õ
video output setting is incorrect.
"
"
i The USB cable (mini-B) is not correctly
connected to the PC or camera.
i The PC is not turned on.
image
on
the
i Camera malfunction.
i The batteries have run out.
The camera has suffered an unforeseen
problem.
print
with
®
"
" PICTBRIDGE is not selected in "
USB mode in the "
˜
" SET-UP menu.
was
Solutions
Unprotect frames using the camera on
which the protection was first applied.
1Press the "MENU/OK" button to display
the menu.
2Press "a" or "b" to select " ˜ " SET-UP
and press "c".
3Press "a" or "b" to select " ô "
4Press "c".
5Press "a" or "b" several times to select
"ENGLISH".
6Press the "MENU/OK" button.
i After the movie playback mode is
stopped, connect the camera and TV
correctly.
i Connect the camera and TV correctly.
i Set the TV input to "VIDEO".
i Change the setting to "NTSC" or "PAL"
(➡P.92).
i Adjust the volume.
Change the setting to "NTSC" or "PAL"
(➡P.92).
i Set up the camera and the USB cable
(mini-B) correctly.
i Turn the PC on.
i Briefly remove the batteries or
disconnect the AC power adapter. Then
reload the batteries or reconnect the AC
power adapter and try again.
i Load new or fully charged batteries.
Briefly remove the batteries or disconnect
the AC power adapter. Then reload the
batteries or reconnect the AC power
adapter and try again. If you think the
camera is faulty, contact your FUJIFILM
dealer.
ò
®
ò
"
Select "
" PICTBRIDGE in "
" USB
mode in the "
˜
" SET-UP menu.
Perform steps 1 to 3 to remove the
camera from a PC.
h Windows
1 The "New Hardware Found" wizard (or
"Scanner and Camera" wizard)
appears. If the wizard does not appear,
proceed to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the PC.
h Macintosh
1 The window for locating the driver
appears. If the window does not
appear, proceed to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the
Macintosh.
125
Advertisement
Table of Contents
