Channel Setting; Clock Setup - Sharp Aquos LC-20B6M Operation Manual

Preset (Continued)

Channel Setting

1
Press MENU to display the MENU screen.
2
Press \/| to select "Setup".
3 Press '/" to select "CH setup", and press OK.
M e n u [ S e t u p : C H
M e n u
P i c t u r e P i c t u r e S o u n d S o u n d S e t u p S e t u p
C H
C l o c k
D i s p l a y
T e r m i n a l
A V 2
P C
L a n g u a g e
4
Press '/" to select the desired adjustment item.
M e n u [ S e t u p : C H
M e n u
A d j u s t s e t t i n g
P o s i t i o n
C o l o u r s y s t e m
S o u n d s y s t e m
S k i p
F i n e
N I C A M
A 2
5 Each time you press \/|, the setting for individual
items changes as shown in the table below.
6
Press MENU to exit.
Selected item
Position The channel position changes to the upper or lower number.
Colour system The mode changes in the following order:
PAL
Auto
PAL60 N443
Sound system The mode changes in the following order:
B/G I D/K M
Skip The mode changes in the following order:
On ←→ ←→ ←→ ←→ Off
←→
Channel numbers with a "● (RED)" mark on the left are set
to Skip.
To turn off Skip, press Channel Select to select the desired
channel, and then set the Skip mode on the CH setup menu
to "Off".
Fine The frequency changes to allow fine tuning.
NICAM The broadcast sound system changes in the following order:
On (NICAM sound) ←→
A2 Stereo system changes in the following order:
On (A2 sound) ←→
NOTE
• Switching Colour system;
Set the system to Auto for normal TV reception. The Auto mode
automatically detects the receiving signal system and changes the
reception system of the LCD TV set. When the picture or sound is
not stable, switching to an appropriate system may improve the
picture or sound quality.
• When using Fine tuning, the channel number changes from green
to yellow.
• To return the channel to its original frequency setting, follow the
manual channel preset procedure. (Please see page 13 "Preset-
ting the Channels (MANUAL)" for details.)
14
s e t u p ]
F e a t u r e s F e a t u r e s
s e t u p
s e t u p
m o d e
s e l e c t
I n / O u t
s e t u p
s e t u p ]
C H 1
S E C A M
B / G
O f f
8 7 1 . 1 5 M H z
O n
O n
Description
SECAM
N358
←→ Off (Monaural TV sound) ←→ ←→
←→
←→ ←→ Off (Monaural TV sound) ←→
←→

Clock Setup

The Timer functions that turn power on at the specified time
do not work unless the clock has been adjusted. Be sure to
adjust the clock first.
1
Perform steps 1 and 2 in Channel Setting to display
the Setup Menu screen.
2
Press '/" to select "Clock setup", and press OK.
M e n u [ S e t u p : C l o c k
M e n u
S e t u p
P i c t u r e S o u n d F e a t u r e s
C H s e t u p
C l o c k
D i s p l a y
T e r m i n a l
A V 2 I n / O u t
P C s e t u p
L a n g u a g e
3
Press '/" to set the time, and press OK.
• Holding down '/" changes the setting at a high speed.
M e n u [ S e t u p : C l o c k M e n u
A d j u s t s e t t i n g
0 0 : 0 0 : 0 0
4
Press MENU to exit.
■ Backup
The clock function is maintained for about 10 minutes even when the
adapter has been shut off due to a power outage or when moving
the LCD TV set. (Since about 30 minutes are required to charge the
backup power supply, the clock function may not be able to be
maintained if the charging time is excessively short.)
s e t u p ]
s e t u p
m o d e
s e l e c t
s e t u p ]