Page 1
DAY/NIghT RIFlEScopE SYSTEm ATN 4-12x80 DNS ATN 2-6x68 DNS u s e r ` s g u i d e Impor tant Expor t Restrictions ! Commodities, products, technologies and services contained in this manual are subject to one or more of the export control laws and regulations of the U.S.
Page 3
Lens coatings • Sun shade • Sun shade * ATN reserves the right to change the above specifications at any time without notice ApplIcATIoN ATN is proud to present our unique day/night riflescope systems. This unit starts as a sensational daytime scopes. 80mm (!) objective and 40mm(!) tube combined with the best, German quality multi-coated glass on the market make this sight the best light- gathering device for shooting in the world.
Each ATN scope is furnished with a set of non-offset rings usable with any Weaver or Picatinny style mount. These may also be reversed for more inter ring distance options or the recoil lug on the underside of each ring can be reversed (turned 180 degrees) by removing the two screws attaching it to the ring.
Page 5
Remove the tops of both rings and Figure 1 inserts and cradle the scope in their lower halves. Install the top halves and tighten each ring’s four screws to finger tight (Figure 1). Do not over tighten or you will be unable to rotate the offset inserts.
Page 6
SIghT IN YouR RIFlE Chances are your rifle will not shoot to your bore sighted zero or to the zero you desire. This is primarily due to the rifles recoil impulse prior to the bullets departing the barrel. Recoil for RH twist barrels tends to carry the shot up and to the left. If you are more than 1 inch in any direction from the center of the bull or from your desired zero, adjust the scope using the rings insert mechanism or the rings side nuts as described above.
Page 7
pRE-zERoINg Pre-zeroing is recommended and can be done with a scope guide or bore sight. These items have their own instructions. CAUTION: Be sure gun is not loaded. Use safe gun handling procedures all the time. zERoINg CAUTION: All shooting should be done at an approved range or other safe area. Eye and ear protection is recommended.
Page 8
ATN RANgEFINDER RETIclE The rangefinder reticle in your riflescope was designed to assist you in determining the range of your target. These dis- tances are based on a 6’ target, if a 6’ target fits between the numbered baseline (the five short horizontal lines) and the post of the reticle above the baseline determines your dis- If a 6’...
Page 9
(it will void your warranty). If your scope ever does need any repair or adjustment, it should be returned to ATN’s service department. The exposed optical surfaces will perform their best if they are wiped clean from time to time with a lens cloth or with optical quality lens paper like those for eyeglasses or camera lenses.
Page 10
REplAcINg DAY-VISIoN EYEpIEcE wITh NIghT-VISIoN oNE Release the detent along arrow “Open” on the sight body, turn it counter clock- wise and take it out. In order to install the night-vision sight align the bayonet groove in the eye- piece body with the pin (or finger) on the interior surface of the sight body (its location is marked with a dot on the body), insert the eyepiece as far as it will go then turn it clockwise.
pREpARINg FoR opERATIoN Day tim e Snip er S cop e : • Install the battery for illuminated reticle into its housing. • Adjust the magnification by rotating the magnification ring near eyepiece. • Observe the scene and adjust the eyepiece for optimal clarity. Get focus by rotating the focusing ring of the eyepiece.
Adjust the potentiometer, to reduce bright- ness. Q: A pattern of dark thin lines which look like chicken wire. S: Turn on illuminator, if purchased. If illuminator doesn’t brighten image, replace batter- ies. If problem persists, contact ATN for service instructions.
ATN, at its option, will either repair or replace the product, and such action on the part of ATN shall be the full extent of ATN’s liability, and the Customer’s sole and exclusive remedy. This warranty does not cover a product (a) used in other than its normal and customary manner;...
Merchandise Authorization number (RMA). When returning please take or send the product, postage paid, with a copy of your sales receipt to our service center, ATN Corporation at the address noted above. All merchandise must be fully insured with the correct postage;...