Table of Contents
Advertisement
Quick Links
Trademarks
Copyright PLANET Technology Corp. 2004.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. The information
in this manual is subject to change without notice. All other trademarks belong
to their respective owners.
FCC Warning
This equipment has been tested and found to comply with the regulations for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this user's guide, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
REVISION
User's manual for PLANET Intelligent Media Converter
For Models: WFT-201, WFT-202, WFT-202S15
Rev 2.0 (Nov. 2004)
Part No. EM-WFT20xv2
EM-WFT20xv1.indd
1
2004/11/5,
12:01
Advertisement
Table of Contents
Related Manuals for Planet WFT-201
Summary of Contents for Planet WFT-201
-
Page 1: Fcc Warning
Copyright PLANET Technology Corp. 2004. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject to change without notice. All other trademarks belong to their respective owners. -
Page 2: Table Of Contents
Table of Contents Chapter 1 INTRODUCTION 1.1 Overview of this User’s Manual Chapter 2 UNPACKING AND SETUP Unpacking Setup Chapter 3 IDENTIFYING EXTERNAL COMPONENTS Front Panel LED Indicators Chapter 4 CONFIGURE THE MEDIA CONVERTER Configure Through Terminal Emulator/TELNET Program Configure Through Web browser Chapter 5 SPECIFICATIONS EM-WFT20xv1.indd... -
Page 3: Chapter 1 Introduction
Chapter 1 Introduction The Intelligent 10/100Base-TX to 100Base-FX Media Converter series (WFT-20x) support the conversion of different media between the copper Fast Ethernet (10/100Base-TX) and fiber Fast Ethernet (100Base-FX). The WFT-20x had built-in Micro Processor to monitor the WFT-20x status and to configure the device’s advanced function. - Page 4 This page is intentionally left blank EM-WFT20xv1.indd 2004/11/5, 12:01...
-
Page 5: Chapter 2 Unpacking And Setup
Chapter 2 Unpacking and Setup This chapter provides unpacking and setup information for the WFT-20x. 2.1 Unpacking Open the box of the WFT-20x and carefully unpack it. The box should contain the following items: • One Intelligent Media Converter • One Power Cord •... - Page 6 This page is intentionally left blank EM-WFT20xv1.indd 2004/11/5, 12:01...
-
Page 7: Chapter 3 Identifying External Components
Chapter 3 Identifying External Components This section identifies all the major external components of the WFT-20x. The front panel is shown, followed by a description of each panel feature. The indicator panel is described in detail in the next chapter. 3.1 Front Panel The figure below shows the front panels of the WFT-20x. -
Page 8: Led Indicators
3.2 LED Indicators Lights Green power is inserted Lights Amber power is inserted and it is fail (System CPU) Blinks Green the data is transmitting CONSOLE Blinks Amber transmitting the wrong data FAIL Lights Amber the link is fail (TP/Fiber) Lights Green when link to networking Ethernet LNK/ACT... -
Page 9: Chapter 4 Configure The Media Converter
Chapter 4 Configure The Media Converter This chapter helps you how to configure the WFT-20x. 4.1 Configure Through Terminal Emulator/TELNET Program 4.1.1 Terminal Emulator program setting The WFT-20x can be accessed using a terminal or terminal emulator attached to the RS- 232 serial port. - Page 10 4.1.3 Configure the Intelligent WFT-20x 4.1.3.1 Main Menu The main menu shows the setting of the File, General Configuration, System Configuration, Device Configuration, SNMP Configuration and Device Status. 4.1.3.2 Files To set the Software Reboot, Factory Reset and Image Update. 4.1.3.2.1 Software Reboot After configuring the software, you need to reboot the device by pressing the Software Reboot to change the setting.
- Page 11 4.1.3.3 General Configurations This page is to configure the device name, passwords and location. • Hardware revision: noted the version of the hardware. • BIOS revision: noted the version of the BIOS. • Firmware revision: noted the version of the firmware. •...
- Page 12 4.1.3.5 Device Configurations This page needs to configure the Copper and Fiber Setting. • Copper Setting: to set the Auto-Negotiation Mode, Duplex mode, Speed, Flow Control and Link Enable setting. • Auto-Negotiation: when set to “Auto”, it will detect the speed from other end if it will be 10Mbps or 100Mbps and will set itself to be the same speed, and when set to “Force”...
-
Page 13: Configure Through Web Browser
• Cold Start trap: to set the trap for rebooting the device (default = enable). • Authentication Fail Trap: to set the warning trap when the community name of the device and workstation are different (default = enable). • MC Link Up Trap: to enable the trap that if other device has linked up. •... -
Page 14: System Reboot
4.2.1 System Reboot After configuring the converter, you need to reboot the device by pressing the System Reboot to access the new setting. 4.2.2 Factory Reset This function is to set the device back to the factory default setting in case of the messy setting. -
Page 15: System Configuration
4.2.5 General Configuration This page is to configure the device name, passwords and location. • Hardware revision: noted the version of the hardware. • BIOS revision: noted the version of the BIOS. • Firmware revision: noted the version of the firmware. •... - Page 16 4.2.7 Device Configuration This page needs to configure the Copper and Fiber Setting. • Copper Setting: to set the Auto-Negotiation Mode, Duplex mode, Speed, Flow Control and Link Enable setting. • Auto-Negotiation: when set to “Auto”, it will detect the speed from other end if it will be 10Mbps or 100Mbps and will set itself to be the same speed, and when set to “Force”...
- Page 17 • Cold Start trap: to set the trap for rebooting the device (default = enable). • Authentication Fail Trap: to set the warning trap when the community name of the device and workstation are different (default = enable). • MC Link Up Trap: to enable the trap that if other device has linked up. •...
- Page 18 This page is intentionally left blank EM-WFT20xv1.indd 2004/11/5, 12:01...
-
Page 19: Chapter 5 Specifications
Fiber: FAIL, LINK/ACT, FDX/COL 10Base-T: 2-pair UTP Cat. 3,4,5, up to 100 m (328 ft) 100Base-TX: 2-pair UTP Cat. 5, up to 100 m (328 ft) 100Base-FX: WFT-201, WFT-202 – Cable 62.5/125μm or 50/125μm multi-mode fiber optic up to WFT-202S15 –... - Page 20 This page is intentionally left blank EM-WFT20xv1.indd 2004/11/5, 12:01...
- Page 21 EM-WFT20xv1.indd 2004/11/5, 12:01...
- Page 22 Part No.:EM-WFT20xv2 EM-WFT20xv1.indd 2004/11/5, 12:01...