Turing On Your System With No Entry Time; Turning On Your System Automatically (Automatic Arming) - DSC Envoy NT9010 User Manual

Announcement: Problem and how it should be addressed:
"Device low battery, Your system has detected that one or more of the wireless
press [7]." detectors on the system has a low battery. Press
tem will announce which devices have a low battery. Change
the relevant batteries. See page 26 for instructions. If this does
not correct the problem, call for service.
"The time and date If all power to the system is interrupted (AC and battery), the
are incorrect." system clock and date will need to be reset. See Setting the
Time and Date on page 21. If you are unsure of the cause of
the system power failure, call for service.
Testing Your Test your system every week. Report any problems immediately to your installation
System company.
NOTE: Perform system tests during off-peak hours, such as early morning
or late evening.
1. If your system has remote monitoring, call the central station to tell them that
you are testing your system.
2. Begin with the system turned off. Press
sounds the siren and turns on all keypad lights for two seconds. When the
sounder and keypad test is complete, press
3. To test each area of your system, open each door and window in turn, or walk
in motion detector areas.
4. Press the Status button. The system will announce all open zones.
5. If the system has any fire zones, activation will cause the alarm to sound in a
pulsed mode. To silence the alarm, press
CAUTION: Do not use an open flame or burning materials to test a smoke
or heat detector. Contact your installer for information on safe methods of
testing detectors.
6. When you are finished testing the system, inform your central station. If the
system did not work properly, contact your installer.
NOTE: Some features described above will not be functional unless
enabled by your installer. Ask your installer which features are functional
on your system.
Allowing From time to time, your installer may need to send information to, or retrieve
Computer information from your security system. Your installer will call your system over the
Access to Your telephone line using a computer. You may need to prepare your system to receive
System this "downloading" call. To do this:
1. Press [Master code]
6
depending your installer's set up. During this time, the system will answer
incoming downloading calls.
For more information on this feature, please ask your installer.
20
, and the sys-
7
[Master Code] . The system
4
6
.
#
.
#
. This allows downloading for 1 or 6 hours
5
Tu r n in g Y o u r S ys t em O n (A r m in g ) an d O f f ( Di sar mi n g)
NOTE: Pressing will only turn on the system. To turn the system off,
0
you must enter a valid [access code]. See Turning Off Your System on page
10.
Turing On If you want to turn on the system, and no one else will be entering, you can
Your System remove the entry time from zones that normally have one. If somebody enters
with No Entry through any zone, the system will sound an instant alarm.
Time
1. Check that your system is ready (green Ready light is ON)
2. Press , then your [access code].
9
• The red (Armed) light flashes as a reminder that the system is on and has
no entry time.
• The keypad sounds fast beeps.
3. The system is now in Stay mode.
Turning On Your installer may have set up your system to turn on at a pre-set time. If auto-
Your System
matic arming has been set up, when the system reaches the pre-set autoarm time,
Automatically the keypad buzzers will sound for one minute.
(Automatic
During this one-minute warning time, you may be able to stop automatic arming
Arming)
by entering your [access code]. Ask your installer for more information.
Your installer may have set up the system so that users with a master code can
change the autoarm time at the keypad. If so, master users will be able to turn the
automatic arming function on or off, and program the time at which the system
will automatically turn on each day.
To turn automatic arming on or off:
1. Press , then [master code].
6
2. Press to turn automatic arming on or off. The keypad will beep 3 times
2
when auto-arm is turned ON, and once when it is turned OFF.
3. When you are finished, press
To change the autoarm time:
1. Press , then [master code].
6
2. Press .
3
3. Enter the autoarm time using the 24Hr format (0000 - 2359). For example, to
set the time for 1:00pm, enter (1300).
5. When you are finished, press
NOTE: The system must have the correct time and date in order for the
autoarm feature to work. Please seeSetting the Time and Date on page 21.
.
#
twice.
#
13