Sound Active Mode; Auto Run Mode - American DJ Mega Go Flood Par User Instructions

Mega Go Flood Par
as the ADJ Show Designer™.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Mega
Go Flood Par has 7 DMX modes: 1 Channel mode, 2 Channel mode,
3 Channel mode, 4 Channel mode, 5 Channel mode, 6 Channel
mode, and a 7 Channel mode. See pages 16-20 for each modes'
DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"A.XXX" is displayed. "XXX" represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
To run the 1 Channel Mode, press the MODE button until "Ch.01"
is displayed. This is the 1 Channel DMX Mode.
To run the 2 Channel Mode, press the MODE button until "Ch.02"
is displayed. This is the 2 Channel DMX Mode.
To run the 3 Channel Mode, press the MODE button until "Ch.03"
is displayed. This is the 3 Channel DMX Mode.
To run the 4 Channel Mode, press the MODE button until "Ch.04"
is displayed. This is the 4 Channel DMX Mode.
To run the 5 Channel Mode, press the MODE button until "Ch.05"
is displayed. This is the 5 Channel DMX Mode.
To run the 6 Channel Mode, press the MODE button until "Ch.06"
is displayed. This is the 6 Channel DMX Mode.
To run the 7 Channel Mode, press the MODE button until "Ch.07"
is displayed. This is the 7 Channel DMX Mode.
4. Please see pages 16-20 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
ADJ Products, LLC - www.adj.com - Mega Go Flood Par User Manual Page 11
Operating Instructions Mega Go Flood Par
RGB Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When "r.XXX" is displayed you are in Red dimming mode. Press
the UP and DOWN buttons to adjust intensity.
3. When "G.XXX" is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When "b.XXX" is displayed you are in Blue dimming mode. Press
the UP and DOWN buttons to adjust intensity.
5. After you have adjusted the RGB colors to make your desired
color you can then activate strobing by pressing the SET UP but-
ton to enter the Flash (strobe) mode.
6. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).

Sound Active Mode:

In this mode the Mega Go Flood Par will react to sound, and chase
through the different colors.
1. Plug the fixture in and press the MODE button until "SoXX" is dis-
played. "XX" represents the sound active mode (1-15) currently
displayed.
2. The fixture will now change via sound.
3. Press the SET UP button to adjust the sound sensitivity. "SJ-X"
should be displayed. Use the UP or DOWN buttons to adjust the
sensitivity. "SJ-1" is the lowest sensitivity, "SJ-8" is the highest.

Auto Run Mode:

In this mode the Mega Go Flood Par will run 1 of 16 auto programs.
The auto run program can be either a fade program or a simple color
change program.
1. Plug the fixture in and press the MODE button until "APXX" is dis-
played. "XX" represents the program number (1-16) currently dis-
played.
2. After you have chosen your desired program you need to decide
if you would like the program to fade through colors or simply
change. Press the SET UP button until either "SP.XX" (color
change speed) or "F-XX" (color fade speed) is displayed.
3. If you select color change, use the UP and DOWN buttons to
adjust the speed between "SP.01" (slowest) and "SP.99" (fastest).
ADJ Products, LLC - www.adj.com - Mega Go Flood Par User Manual Page 12
Operating Instructions