Table of Contents
Advertisement
Troubleshooting
The driver cannot be installed.
• Is the USB cable connected correctly?
¡ Check the USB cable connection. (MAGICSTOMP's Owner's Manual)
¡ Disconnect the USB cable, then connect it again.
Windows
• Is the USB function enabled on your computer?
¡ When you connect the MAGICSTOMP to the computer for the first time,
if the "Add New Hardware Wizard"
function on the computer may be disabled. Perform the following steps.
1 Select [Control Panel] ¡ [System] ¡ [Device Manager] (for Windows
98/Me), or select [Control Panel] (Windows XP: Classic View) ¡
[System] ¡ [Hardware] ¡ [Device Manager] (for Windows 2000/XP).
2 Make sure that no "!" or "x" marks appear at "Universal serial bus
controller" or "USB Root Hub." If you see an "!" or "x" mark, the USB
controller is disabled. For more information, refer to the owner's
manual of your computer.
• Is any unknown device registered?
¡ If driver installation fails, the MAGICSTOMP will be marked as an
"Unknown device," and you will not be able to install the driver. Delete the
"Unknown device" by following the steps below.
1 Select [Control Panel] ¡ [System] ¡ [Device Manager] (for Windows
98/Me), or select [Control Panel] (Windows XP: Classic View) ¡
[System] ¡ [Hardware] ¡ [Device Manager] (for Windows 2000/XP).
2 Look for "Other devises" in the menu "View devices by type."
3 If you find "Other devices," double-click it to extend the tree to look
for "Unknown device." If one appears, select it and click the [Remove]
button.
4 Remove the USB cable from the MAGICSTOMP, and make the
connection again.
5 Install the driver again. (page2)
When controlling the MAGICSTOMP from
your computer via USB, the MAGICSTOMP
does not operate correctly or no sound is
heard.
• Did you install the driver? (Windows: page2, Macintosh: page7)
• Is the USB cable connected correctly? (MAGICSTOMP's Owner's Manual)
• Is the volume turned up on the MAGICSTOMP, playback equipment, or
application?
• Is the proper port selected in the Sound Editor for MAGICSTOMP?
• Is the latest driver installed?
• Is the effect switched "OFF"? Is the MAGICSTOMP in the Tuner Mode,
Store Mode, or Name Edit Mode? Make sure the MAGICSTOMP is in its
normal operating mode (select a patch and switch the effect "ON").
Cannot suspend or resume the computer
correctly.
• If you are using Windows 2000, you may not be able to suspend/resume
normally, depending on the particular environment (USB Host Controller,
etc.). Even so, simply disconnecting and connecting the USB cable will allow
you to use the MAGICSTOMP functions again.
(page2,
4) does not appear, the USB
How can I delete or re-install the driver?
Windows Me/98
1 When the MAGICSTOMP is recognized correctly, double-click
"System" in the Control Panel to open the System window.
2 Double-click the "Device Manager" tab, select "YAMAHA USB MIDI
Driver" and delete it.
3 Use the MS-DOS prompt or Explorer to delete the following three
files.
n
To delete the files below using Explorer, select "Folder Options"
from the Tool (View) menu, and select "Show all files (and folders)."
• \WINDOWS\INF\OTHER\YAMAHAUB99.INF
• \WINDOWS\SYSTEM\Xgusb.drv
• \WINDOWS\SYSTEM\Ymidusb.sys
4 Disconnect the USB cable.
5 Restart the computer.
6 Re-install the driver. (page2)
Macintosh
1 Delete the files in the following locations:
• System Folder | Control Panels | YAMAHA USB MIDI Patch
• System Folder | Extensions | USB YAMAHA MIDI Driver
• System Folder | OMS Folder | YAMAHA USB MIDI OMS Driver
2 Restart the computer.
3 Install the driver (page7) and set up OMS (page9).
SOFTWARE for MAGICSTOMP
11
Installation Guide
Advertisement
Table of Contents
