Distortion Multi (Chorus) - Yamaha Magicstomp Effect List

Distortion Multi (Chorus)

Multi effect consisting of Comp + Distortion + Chorus + Delay + Reverb. Mainly used for direct connection to guitar
amp's front input.
Parameter Display
Type TYPE
Gain GAIN
Master MSTR
Tone TONE
EQ 1 Freq. EQ1F
EQ 1 Gain EQ1G
EQ 1 Q EQ1Q
EQ 2 Freq. EQ2F
EQ 2 Gain EQ2G
EQ 2 Q EQ2Q
EQ 3 Freq. EQ3F
EQ 3 Gain EQ3G
EQ 3 Q EQ3Q
EQ 4 Freq. EQ4F
EQ 4 Gain EQ4G
EQ 4 Q EQ4Q
Pre EQ Level PELV
Pre EQ 1 Freq. PE1F
Pre EQ 1 Gain PE1G
Pre EQ 1 Q PE1Q
Pre EQ 2 Freq. PE2F
Pre EQ 2 Gain PE2G
Pre EQ 2 Q PE2Q
Pre EQ 3 Freq. PE3F
Pre EQ 3 Gain PE3G
Pre EQ 3 Q PE3Q
Comp. Threshold CTHR
Comp. Ratio CRAT
Comp. Attack CATT
Comp. Release CREL
Comp. Knee CKNE
Comp. Gain CGAI
N. G. Threshold NGTH
N. G. Attack NGAT
N. G. Hold NGHL
N. G. Decay NGDC
Wave WAVE
Chorus Delay CHDT
Chorus Speed CHSP
Chorus Depth CHDP
Chorus Level CHLV
FB. Delay DTFB
Tap L DT.L
Tap R DT.R
Delay FB. Gain D.FB
Delay High D.HI
Delay Level DLVL
High Pass Filter DHPF
Low Pass Filter DLPF
Reverb Ini. Delay RIDL
Reverb Time RT
Reverb High R.HI
Reverb Diffusion RDIF
Reverb Density RDNS
Reverb Level RLVL
Range
Lead1, Lead2, Drive1, Drive2,
Crunch1, Crunch2, Fuzz1,
Fuzz2, Distortion1, Distortion2,
Overdrive1, Overdrive2, Tube,
Solidstate, Bypass
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
50.0 to 400 Hz
-12.0 to 12.0 dB
0.100 to 20.0
200 to 1.6 Hkz
-12.0 to 12.0 dB
0.100 to 20.0
600 to 4.80 kHz
-12.0 to 12.0 dB
0.100 to 20.0
2.00 k to 16.0 kHz
-12.0 to 12.0 dB
0.100 to 20.0
0.0 to 10.0
50.0 to 500 Hz
-12.0 to 12.0 dB
0.100 to 20.0
200 to 2.00 kHz
-12.0 to 12.0 dB
0.100 to 20.0
1.00 k to 10.0 kHz
-12.0 to 12.0 dB
0.100 to 20.0
-54.0 to 0.0 dB
1:1 to ∞:1
0 to 120 ms
6 to 11500 ms
Hard, 1 to 5
0.0 to 18.0 dB
0.0 to 10.0
0.0 to 120 ms
0.02 to 2040 ms
6 to 44500 ms
Sine, Triangle
0.0 to 30.0 ms
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
0.0 to 1000.0 ms
0 to 100 %
0 to 100 %
-99 to 99
0.1 to 1.0
0.0 to 10.0
Thru to 8.00 kHz
50.0 Hz to Thru
0.0 to 500.0 ms
0.3 to 99.0 s
0.1 to 1.0 ms
0 to 10
0 to 100
0.0 to 10.0
Distortion type
Adjusts the amount of distortion
Adjusts the volume
Adjusts the tone
Specifies the post effect EQ1 frequency
Specifies the post effect EQ1 gain
Specifies the post effect EQ1 Q (bandwidth)
Specifies the post effect EQ2 frequency
Specifies the post effect EQ2 gain
Specifies the post effect EQ2 Q (bandwidth)
Specifies the post effect EQ3 frequency
Specifies the post effect EQ3 gain
Specifies the post effect EQ3 Q (bandwidth)
Specifies the post effect EQ4 frequency
Specifies the post effect EQ4 gain
Specifies the post effect EQ4 Q (bandwidth)
Specifies the pre effect EQ level
Specifies the pre effect EQ1 frequency
Specifies the pre effect EQ1 gain
Specifies the pre effect EQ1 Q (bandwidth)
Specifies the pre effect EQ2 frequency
Specifies the pre effect EQ2 gain
Specifies the pre effect EQ2 Q (bandwidth)
Specifies the pre effect EQ3 frequency
Specifies the pre effect EQ3 gain
Specifies the pre effect EQ3 Q (bandwidth)
Level at which compressor activates
Compression ratio
Time required for compressor to peak after exceeding threshold
Time required for compressor to terminate after going below threshold
Adjusts the width of the gain curve just above the compressor's threshold
Output level
Level at which the noise gate activates
Time required for the noise gate to open after signal exceeds threshold
Time noise gate stays open
Time required for the noise gate to close after signal goes below thresh-
old
Chorus modulation waveform
Chorus delay time
Chorus speed
Modulation depth
Chorus level
Loop delay time
Left channel delay output time (see
Right channel delay output time (see
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
Delay high-frequency feedback ratio
Delay level
High-pass filter cutoff frequency. For delay, reverb
Low-pass filter cutoff frequency. For delay, reverb
Initial delay before reverb begins
Reverb time
High-frequency reverb time ratio
Left and right reverb spread
Reverb density
Reverb level
27
Description
page 31)
page 31)