Amp Multi (Tremolo) - Yamaha Magicstomp Effect List

Amp Multi (Tremolo)

Multi effect consisting of Comp + Amp Simulator + Tremolo + Delay + Reverb. Mainly used for direct connection to
power amp. Speaker simulator allows direct recording.
Parameter Display
Amp Type TYPE
Gain GAIN
Master MSTR
Tone TONE
Treble TRE
High Middle HMID
Low Middle LMID
Bass BASS
Presence PRE
Speaker
SP
Simulator
N. G. Threshold NGTH
N. G. Attack NGAT
N. G. Hold NGHL
N. G. Decay NGDC
Comp. Threshold CTHR
Comp. Ratio CRAT
Comp. Attack CATT
Comp. Release CREL
Comp. Knee CKNE
Comp. Gain CGAI
Wave WAVE
Tremolo Speed TRSP
Tremolo Depth TRDP
FB. Delay DTFB
Tap L DT.L
Tap R DT.R
Delay FB. Gain D.FB
Delay High D.HI
Delay Level DLVL
High Pass Filter DHPF
Low Pass Filter DLPF
Reverb Ini. Delay RIDL
Reverb Time RT
Reverb High R.HI
Reverb Diffusion RDIF
Reverb Density RDNS
Reverb Level RLVL
Range
Heavy1, Heavy2, Lead1, Lead2,
Drive1, Drive2, Crunch1,
Crunch2, Clean1, Clean2, Solid
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
0.0 to 10.0
Off, American 412, British 412,
Modern 412, YAMAHA 412, Hybrid
412, American 212, British 212,
Modern 212, YAMAHA 212, Hybrid
212, American 112, Modern 112,
YAMAHA 112, Hybrid 112, 410,
210
0.0 to 10.0
0.0 to 120 ms
0.02 to 2040 ms
6 to 44500 ms
-54.0 to 0.0 dB
1:1 to ∞:1
0 to 120 ms
6 to 11500 ms
Hard, 1 to 5
0.0 to 18.0 dB
Sine, Triangle, Squre
0.0 to 10.0
0.0 to 10.0
0.0 to 1000.0 ms
0 to 100 %
0 to 100 %
-99 to 99
0.1 to 1.0
0.0 to 10.0
Thru to 8.00 kHz
50.0 Hz to Thru
0.0 to 500.0 ms
0.3 to 99.0 s
0.1 to 1.0 ms
0 to 10
0 to 100
0.0 to 10.0
Amp type
Adjusts the amount of distortion
Adjusts the volume
Adjusts the tone
Adjusts level of high range frequencies
Adjusts level of upper mid frequencies
Adjusts level of lower mid frequencies
Adjusts level of low frequencies
Adjusts level of extremely high frequencies
When using a line connection to connect directly to a mixer, this can be
used to simulate the natural characteristics of a speaker giving the tone
a more natural sound
Level at which the noise gate activates
Time required for the noise gate to open after signal exceeds threshold
Time noise gate stays open
Time required for the noise gate to close after signal goes below thresh-
old
Level at which compressor activates
Compression ratio
Time required for compressor to peak after exceeding threshold
Time required for compressor to terminate after going below threshold
Adjusts the width of the gain curve just above the threshold
Output level
Modulation waveform
Tremolo speed
Tremolo depth
Loop delay time
Left channel delay output time (see
Right channel delay output time (see
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
Delay high-frequency feedback ratio
Delay level
High-pass filter cutoff frequency. For delay, reverb
Low-pass filter cutoff frequency. For delay, reverb
Initial delay before reverb begins
Reverb time
High-frequency reverb time ratio
Left and right reverb spread
Reverb density
Reverb level
25
Description
page 31)
page 31)