Lenovo Erazer X700 Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Desktop
  5. Erazer X700
  6. Hardware maintenance manual
Lenovo Erazer X700 Hardware Maintenance Manual

Lenovo Erazer X700 Hardware Maintenance Manual

Machine types: 10122/90a2
Hide thumbs Also See for Erazer X700:
Table of Contents

Advertisement

Quick Links

Lenovo Erazer X700
Hardware Maintenance Manual
Machine Types: 10122/90A2

Advertisement

Table of Contents
loading

Related Manuals for Lenovo Erazer X700

Summary of Contents for Lenovo Erazer X700

  • Page 1 Lenovo Erazer X700 Hardware Maintenance Manual Machine Types: 10122/90A2...
  • Page 3 Lenovo Erazer X700 Hardware Maintenance Manual Machine Types: 10122/90A2...
  • Page 4 First Edition (January 2013)31st © Copyright Lenovo 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925...

  • Page 5: Table Of Contents

    Selecting a startup device ..FRU lists ....Exiting the Lenovo BIOS Setup Utility program . . Chapter 9. General information ..51 Chapter 6.
  • Page 6 Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 7: Chapter 1. About This Manual

    Chapter 1. About this manual This manual contains service and reference information for Lenovo Erazer X700 desktop computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2013...
  • Page 10 – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 11: Safety Inspection Guide

    – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury.

  • Page 12: Grounding Requirements

    • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 15: Chapter 3. General Information

    This chapter provides general information that applies to all machine types supported by this publication. Specifications This section lists the physical specifications for your computer. This section lists the physical specifications for your computer. Type Lenovo Erazer X700 This section lists the physical specifications. Environment Air temperature: Operating: 10°...
  • Page 16 Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2013...
  • Page 18 Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 character (a-z, and 0-9).

  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.

  • Page 22: Selecting A Startup Device

    Network Setup press the Enter key, then select Onboard Ethernet Support or LAN Boot Agent. 4. Select Disabled or Enabled and press the Enter key. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save changes and Exit from the menu.

  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 25: Chapter 6. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor(s) connection Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2013...

  • Page 26: Post Error Codes

    3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 27: Chapter 7. Locating Connectors, Controls And Components

    The following illustration shows the components that make up your computer. 1. Power supply 5. Graphics card 2. Heat sink 6. Solid state drive 3. Memory modules 7. Hard disk drive 4. Motherboard 8. System fan © Copyright Lenovo 2013...
  • Page 28 13. Clear CMOS jumper 6. 24-pins power connector 14. PCI Express X 1 adapter slots (2) 7. USB 3.0 connectors (2) 15. PCI Express X 16 graphics adapter slots (2) 8. eSATA connectors 16. Front audio connector Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 29: Chapter 8. Replacing Hardware

    Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo.

  • Page 30: Replacing The Keyboard And Mouse

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 31: Replacing A Memory Module

    Step 4. Remove the two screws that secure the computer cover at the rear of the chassis. Step 5. Lift up the computer cover, then slide it out to remove it. Step 6. To reattach the computer cover: Line up the computer cover with the chassis and place it into position. Secure the computer cover to the chassis with the two screws.

  • Page 32: Replacing The Hard Disk Drive

    Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 33: Replacing A Solid State Drive

    Step 5. Disconnect the data and power cables from the hard disk drive. Step 6. Lift the hard disk drive up and out of the drive bay. Step 7. Remove the two pins to release the hard disk drive from the bracket. Step 8.

  • Page 34: Replacing An Optical Drive

    Connect the data and power cables to the new solid state drive. Step 9. Reattach the computer cover. Replacing an optical drive Note: For this procedure, it helps to lay the computer flat. To replace an optical drive: Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 35 Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer.

  • Page 36: Replacing The Graphic Card

    Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 37: Replacing The Heat-Sink Assembly

    Step 5. Remove the two screws that secure the graphics card to the chassis. Step 6. Disconnect the power cables from the graphics card. Step 7. Push the pin to unlock the graphics card , and then lift up the graphics card to remove it. Step 8.

  • Page 38: Replacing An Intel Cpu

    Reconnect the microprocessor fan power cable to the connector on the motherboard. Step 9. Reattach the computer cover. Replacing an Intel CPU Note: For this procedure, it helps to lay the computer flat. To replace the CPU Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 39 Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer.
  • Page 40 Attention: Do not touch the gold contacts on the bottom of the microprocessor. When handing the microprocessor, touch only the sides. Note: Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 41: Replacing The Power Supply

    Step 7. Holding the sides of the microprocessor with your fingers, remove the protective cover that protects the gold contacts on the new microprocessor. Step 8. Holding the sides of the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are aligned with the tabs in the microprocessor socket.
  • Page 42 Remove the heat-sink assembly. Refer to “Replacing the heat-sink assembly ”. Step 6. Disconnect the power cables from the connectors on motherboard, graphic card, hard disk drive, solid state drive, optical drive. 1 2 3 4 5 6 Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 43 Chapter 8 Replacing hardware...
  • Page 44 Step 10. Install the new power supply： Line up the holes on the new power supply with mounting holes on the rear of the chassis and secure it to the chassis with the 4 screws. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 45: Replacing The Wi-Fi Card

    Reattach the power supply supporting bracket. Connect the power cables to the connectors on the motherboard, graphic card, hard disk drive, solid state drive, optical drive. Reattach the heat-sink assembly. Step 11. Reattach the computer cover. Replacing the Wi-Fi card Note: For this procedure, it helps to lay the computer flat.
  • Page 46 Remove the front bezel. Refer to “Removing the front bezel”. Step 6. Disconnect the data cables from the connectors on rear of card reader module. Step 7. Slide to left to unlock the front card reader module. Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 47 Step 8. Open the front door, then slide out the card reader tray as shown. Chapter 8 Replacing hardware...
  • Page 48 Step 9. Remove the front card reader module top cover as shown. Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 49: Replacing The Motherboard

    Step 10. Remove the 2 screws that secure the card reader module to the bracket, and the pull the card reader module upward to remove it. Step 11. Install the new front card reader module: Line up the new front card reader module with the card port, and then insert the new card reader module into position.

  • Page 50: Replacing The Front I/O Board

    Note: For this procedure, it helps to lay the computer flat. To replace the front I/O board: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 51 Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to “Left and right view” and “Rear view”...
  • Page 52 Step 9. Lift up the rear of the top cover , push the top cover forward gently to release the top cover as shown. Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 53 Step 10. Disconnect the front I/O module cables from the connectors on the motherboard. Step 11. Remove the 2 screws that secure front I/O module to the chassis, then slide out the front I/O module and cables slowly. Chapter 8 Replacing hardware...

  • Page 54: Fru Lists

    • 1– identifies parts that are fairly simple to replace, requiring few or no tools. • 2– identifies parts that are slightly more difficult to replace. • N-identifies parts that are not to be replaced by the customer. Description Service CRU ID part number (FRU) Processor Lenovo Erazer X700Hardware Maintenance Manual...
  • Page 55 I I7-3820 3.6/1600/10/2011 130 M1 CPU 1100509 System board NON_WIN8 MSI X79 MATX MB 90001926 90001927 WIN8 MSI X79 MATX MB WIN8_PRO MSI X79 MATX MB 90001928 Thermal module 31503169 MSI 35-101-1012170 cooler DS12025B12HP076 Fan 31503170 Memory M378B5273DH0CK0 4GB D31600 Memory HF 1100213 Hard drives 16200182...
  • Page 56 Power cord 31049514 豪利士1.8米C13 JAPAN Power Cord 31049523 立讯(博硕)1.8米 C13 JAPAN Power Cord 31039730 LW 1.8m JAPAN Power Cord® 31049514 豪利士1.8米C13 JAPAN Power Cord 31049523 立讯(博硕)1.8米 C13 JAPAN Power Cord LW 1.8m JAPAN Power Cord® 31039730 Lenovo Erazer X700Hardware Maintenance Manual...

  • Page 57: Chapter 9. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2013...

Table of Contents