Lenovo Erazer X310 Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Desktop
  5. Erazer X310
  6. Hardware maintenance manual

Lenovo Erazer X310 Hardware Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Lenovo Erazer X310 Hardware Maintenance
Manual
Machine Types: 90AV [X310 ES];90AU [X310 Non-ES]

Advertisement

Table of Contents
loading

Related Manuals for Lenovo Erazer X310

Summary of Contents for Lenovo Erazer X310

  • Page 1 Lenovo Erazer X310 Hardware Maintenance Manual Machine Types: 90AV [X310 ES];90AU [X310 Non-ES]...
  • Page 3 Lenovo Erazer X310 Hardware Maintenance Manual Machine Types: 90AV [X310 ES];90AU [X310 Non-ES]...
  • Page 4 First Edition (June 2014)15th © Copyright Lenovo 2014. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925...

  • Page 5: Table Of Contents

    Replacing the motherboard..Exiting the Lenovo BIOS Setup Utility program . . FRU lists ....
  • Page 6 Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 7: Chapter 1. About This Manual

    Chapter 1. About this manual This manual contains service and reference information for Lenovo Erazer X310 computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2014...
  • Page 10 – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 11: Safety Inspection Guide

    – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury.

  • Page 12: Grounding Requirements

    • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. Lenovo Erazer X310 Hardware Maintenance Manual...
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 15: Chapter 3. General Information

    This chapter provides general information that applies to all machine types supported by this publication. Specifications This section lists the physical specifications for your computer. This section lists the physical specifications for your computer. Type Lenovo Erazer X310 This section lists the physical specifications. Environment Air temperature: Operating: 10°...
  • Page 16 Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2014...
  • Page 18 Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 character (a-z, and 0-9).

  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.

  • Page 22: Selecting A Startup Device

    Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Lenovo BIOS Setup Utility program (see “Starting the Lenovo BIOS Setup Utility program” on page 13). 2. From the Lenovo BIOS Setup Utility program main menu, select the Startup option.

  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 25: Chapter 6. Symptom-To-Fru Index

    • System Board Power Supply connectors • Microprocessor(s) connection Check the power cord. Power Cord Check the power-on switch. Power-on Switch Additional Service Information This chapter provides additional information that the service representative might find helpful. © Copyright Lenovo 2014...

  • Page 26: Post Error Codes

    2. Remove or disconnect the following components (if connected or installed) one at a time. a. External devices (modem, printer, or mouse) b. Extended video memory c. External Cache d. External Cache RAM e. Hard disk drive f. Disk drive Lenovo Erazer X310 Hardware Maintenance Manual...
  • Page 27 3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. Chapter 6 Symptom-to-FRU Index...
  • Page 28 Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 29: Chapter 7. Locations

    The system board (also known as the “mainboard” or “motherboard”) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The following illustrations show the locations of the different parts on the system board. © Copyright Lenovo 2014...
  • Page 30 LPC debug connector SPI debug connector Clear CMOS jumper Solid state disk power connector Front audio connector SATA connectors (4) PCI express X 1 adapter slots (3) eSATA connector System fan header Power fan header Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 31: Chapter 8. Replacing Hardware

    Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug all power and signal cables from the computer. 3. Place the system on a flat, stable surface. © Copyright Lenovo 2014...

  • Page 32: Replacing The Keyboard And Mouse

    Refer to “Locating connectors on the rear of the computer”. Step 4. Remove the two screws that secure the computer cover at the rear of the chassis. Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 33: Removing The Front Bezel

    Step 5. Slide the computer cover out to remove it. Removing the front bezel Note: For this procedure, it helps to lay the computer flat. To remove the front bezel: Step 1. Remove the computer cover. Refer to “Removing the computer cover”. Step 2.

  • Page 34: Replacing A Memory Module

    Note: For this procedure, it helps to lay the computer flat. To replace a hard disk drive: Step 1. Remove the computer cover. Refer to “Removing the computer cover”. Step 2. Disconnect the data and power cables from the hard disk drive. Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 35: Replacing An Optical Drive

    Step 3. Lift up the plastic handle and slide the hard disk drive out of the drive bay. Step 4. Remove the hard disk drive from the plastic bracket as shown. Step 5. Line up the new hard disk drive with the plastic bracket and snap it into position. Step 6.

  • Page 36: Replacing A Graphics Card

    Remove the screw that secures the graphics card fixing bracket and lift the bracket up. Step 3. Remove the screw that secures the graphics latch to the chassis and open it. Step 4. Disconnect the power cables from the graphics card. Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 37: Replacing The Power Supply

    Step 5. Push the pin to unlock the graphics card , and then lift up the graphics card to remove it. Step 6. To install the new graphics card: Attach the new graphics card to the same adapter connector. Connect the power cables to the new graphics card. Turn the graphics card latch to the closed position and secure it with the screw.

  • Page 38: Replacing The Microprocessor Fan

    “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Disconnect the fan power cable from the connector on the motherboard. Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 39: Replacing The Heat-Sink

    Step 6. Remove the 4 screws that secure the microprocessor fan to the heat-sink and lift up the microprocessor fan to remove it. Step 7. To install the new microprocessor fan: Line up the new microprocessor fan with the heat-sink and secure it to the heat-sink with 4 screws.

  • Page 40: Replacing The Cpu

    Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Remove the microprocessor fan. Refer to “Replacing the microprocessor fan”. Step 6. Remove the heat-sink. Refer to “Replacing the heat-sink”. Lenovo Erazer X310 Hardware Maintenance Manual...
  • Page 41 Step 7. To remove the microprocessor from the system board, press then slide the small handle out to spring it up. and open the retainer. Attention: Do not touch the gold contacts on the bottom of the microprocessor. When handing the microprocessor, touch only the sides.

  • Page 42: Replacing The Wi-Fi Card

    0.03ml (3 tick marks on the grease syringe). Step 13. Reattach the heat-sink, microprocessor fan, computer cover. Replacing the Wi-Fi card Note: For this procedure, it helps to lay the computer flat. Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 43: Replacing The Motherboard

    To replace the Wi-Fi card: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3.

  • Page 44: Fru Lists

    Step 15. Reattach the computer cover. FRU lists This chapter lists the information on the field replaceable units (FRUs). Attention: Be sure to read and understand all the safety information before replacing any FRUs. Lenovo Erazer X310 Hardware Maintenance Manual...
  • Page 45 • 1– identifies parts that are fairly simple to replace, requiring few or no tools. • 2– identifies parts that are slightly more difficult to replace. • N-identifies parts that are not to be replaced by the customer. Description Lenovo P/N CRU ID 　 Haswell & Haswell-Refresh 1100783 I I7-4770 3.4/1600/8/1150 84 CPU...
  • Page 46 31046268 　 11202298 Bitland@Geforce GTX 760@2G/A/2D/DP/HGraphics JT LX-319 K4 Chassis Universal Graphics bracket 31500767 11202804 MSI@Geforce GTX 750@2G/A/2D/mHDMIGraphics MSI@Geforce GTX 745@2G/A/DB/HGraphics 11202802 11202746 MSI@Geforce GT 720@2G/A/DB/HGraphics Bitland@Geforce GT 705@1G/A/DB/HGraphics 11202742 MSI@Geforce GT 705@1G/A/DB/HGraphics 11202743 Lenovo Erazer X310 Hardware Maintenance Manual...
  • Page 47 MGE 4pin to 6pin power cable 150mm 31504075 11202403 Bitland@R5 235@1G/A/DB/HGraphics MSI@R5 235@1G/A/DB/HGraphics 11202404 11202748 Bitland@R5 235@2G/A/DB/HGraphics Bitland@R7 240@2G/A/DB/HGraphics 11202407 VIDEO_CARD M@R9 260@2G/A/DB/D/DP/H SV10G52022 VIDEO_CARD B@Geforce GTX 750Ti@2G/A/DBDH SV10G52021 11202506 MSI@R9 255@2G/A/D/DP/HGraphics 　 36200083 Huntkey HK280-22GP S5 PS3 180W PSU Acbel API6PC06-EL3G PS3 180W PSU 36200084 Liteon PS-5181-8VS2-ROHS PS3 180W PSU...
  • Page 48 Chicony TGR1226 2.4G touchpad BLK final 25212969 　 KB/MOUSE Sunrex EKB-10YA(US) B-Silk USB KB-LVT8 25209111 Primax KB4721(US) B-Silk USB KB-LVT8 25209112 Chicony KU-1153(US) B-Silk USB KB-LVT8 25209113 Sunrex EKB-10YA(TW) B-Silk USB KB-LVT8 25209114 25209115 Sunrex EKB-10YA(TH) B-Silk USB KB-LVT8 Lenovo Erazer X310 Hardware Maintenance Manual...
  • Page 49 Sunrex EKB-10YA(DU) B-S USB KB-LVT8 25209139 25200528 Liteon LXH-SM-8825 B-Silk Mouse Sunrex LXH-EMS-10ZA B-Silk Mouse 25200530 25013797 Lenovo laser mouse M6811(B) Primax M300 USB gesture mouse BLK 25213876 Liteon SK-8861(US) 2.4G KB-Black8 25209175 Liteon SK-8861(US-MY) 2.4G KB-Black8 25209176 Liteon SK-8861(TW) 2.4G KB-Black8 25209177 Liteon SK-8861(TH) 2.4G KB-Black8...
  • Page 50 Liteon SM-8861 Mouse(No Battery) Black Liteon SM-8861(JP) Mouse-Black 25205773 25203466 Liteon SM-8861 Mouse(MY) Black 　 Gaming KB&Mouse 25210203 Chicony KU-0603(US) USB gaming KB Chicony KU-0603(IN) USB gaming KB 25216248 25213791 Newmen MS-172 USB gaming mouse black Lenovo Erazer X310 Hardware Maintenance Manual...

  • Page 51: Chapter 9. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2014...

Table of Contents