Lenovo 10140/90AC Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Desktop
  5. 10140/90AC
  6. Maintenance manual
Lenovo 10140/90AC Maintenance Manual

Lenovo 10140/90AC Maintenance Manual

Gaming desktop
Hide thumbs
Table of Contents

Advertisement

Quick Links

Lenovo Erazer X510
Hardware Maintenance Manual
Machine Types: 10140/90AC;10143/90AD

Advertisement

Table of Contents
loading

Related Manuals for Lenovo 10140/90AC

Summary of Contents for Lenovo 10140/90AC

  • Page 1 Lenovo Erazer X510 Hardware Maintenance Manual Machine Types: 10140/90AC;10143/90AD...
  • Page 3 Lenovo Erazer X510 Hardware Maintenance Manual Machine Types: 10140/90AC;10143/90AD...
  • Page 4 First Edition (August 2013)16th © Copyright Lenovo 2013, 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.

  • Page 5: Table Of Contents

    Selecting a startup device ..Replacing the motherboard..Exiting the Lenovo BIOS Setup Utility program . . Chapter 9. FRU lists ..49 Chapter 6.
  • Page 6 Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 7: Chapter 1. About This Manual

    This manual contains service and reference information for Lenovo Erazer X510 desktop computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2013, 2013...
  • Page 10 – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 11: Safety Inspection Guide

    – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury.

  • Page 12: Grounding Requirements

    • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. Lenovo Erazer X510Hardware Maintenance Manual...
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 15: Chapter 3. General Information

    This section lists the physical specifications. Environment Air temperature: Operating: 10° to 35°C Transit: -20° to 55°C Humidity: Operating: 35% to 80% Transit: 20% to 90% (40°C) Altitude: 86KPa to 106KPa Electrical input: Input voltage: 90V-264V(AC) Input frequency: 47Hz-63Hz © Copyright Lenovo 2013, 2013...
  • Page 16 Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2013, 2013...
  • Page 18 Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 character (a-z, and 0-9).

  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.

  • Page 22: Selecting A Startup Device

    Network Setup press the Enter key, then select Onboard Ethernet Support or LAN Boot Agent. 4. Select Disabled or Enabled and press the Enter key. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save changes and Exit from the menu.

  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 25: Chapter 6. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor(s) connection Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2013, 2013...

  • Page 26: Post Error Codes

    3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 27: Chapter 7. Locating Connectors, Controls And Components

    10. Optical drive 4. Headphone connector 11. Expansion 5.25" ODD bay 5. Microphone connector 12. Hot-swappable hard disk frame 6. USB 3.0 connector / USB power off charging connector 13. Front LED light 7. Overclock button © Copyright Lenovo 2013, 2013...
  • Page 28 9. PCI Express X 16 graphics adapter slot (some models are equipped with a graphics card) 5. USB 3.0 connectors 10. PCI Express X 1 adapter slots (some models are equipped with a WIFI card or TV tuner card) Lenovo Erazer X510Hardware Maintenance Manual...
  • Page 29 Hardware components The following illustration shows the components that make up your computer. 1. Optical disk drive 5. Heat-sink and system fan 2. Hot-swappable hard disk 6. Memory module 3. Hard disk drive 7. Power supply 8. Motherboard 4. Graphics card Chapter 7 Locating connectors, controls and components...
  • Page 30 8. Thermal sensor header 19. PCI express X 1 adapter slots (2) 9. Power connector 20. PCI express X 16 adapter slots (2) 10. Front USB 3.0 connector 21. System fan header 11. eSATA connector Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 31: Chapter 8. Replacing Hardware

    Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo.

  • Page 32: Replacing The Keyboard And Mouse

    Note: For this procedure, it helps to lay the computer flat. To replace the power cord: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 33: Removing The Computer Cover

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 34: Replacing A Memory Module

    Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Locate the memory module connectors. Refer to “Locating components”. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 35: Replacing The Hard Disk Drive

    Step 6. Remove the memory module being replaced by opening the retaining clips as shown. Step 7. Position the new memory module over the memory connector. Make sure the notch on the memory module is correctly aligned with the connector key on the system board.

  • Page 36: Removing The Front Bezel

    Connect the data and power cables to the new hard disk drive. Step 8. Reattach the computer cover. Removing the front bezel Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 37: Replacing An Optical Drive

    Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 38 To install the new optical drive: Line up the locking bracket with mounting holes, then reattach the locking bracket to the optical disk drive. Slide the new optical drive into the bay from the front until it snaps into position. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 39: Replacing The Graphic Card

    Connect the data and power cables to the new disk drive. Step 10. Reattach the front bezel and computer cover. Replacing the graphic card To replace the graphic card: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.
  • Page 40 Step 10. To install the new graphic card: Install the new adapter into the same adapter connector and secure it to chassis with the screw. Close the adapter latch, reattach the metal bracket and secure the bracket with the screw. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 41: Replacing The Heat-Sink & Fan Assembly

    Step 11. Reattach the computer cover. Replacing the heat-sink & fan assembly Note: For this procedure, it helps to lay the computer flat. To replace the heat-sink and fan assembly: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

  • Page 42: Replacing An Intel Cpu

    Attention: Do not touch the gold contacts on the bottom of the microprocessor. When handing the microprocessor, touch only the sides. Note: Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Lenovo Erazer X510Hardware Maintenance Manual...
  • Page 43 Step 7. Holding the sides of the microprocessor with your fingers, remove the protective cover that protects the gold contacts on the new microprocessor. Step 8. Holding the sides of the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are aligned with the tabs in the microprocessor socket.

  • Page 44: Replacing The Power Supply

    Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 45: Replacing The Wi-Fi Card

    Step 5. Remove the four screws that secure the Power supply to the chassis. Step 6. Slide then lift the Power supply out of chassis. Step 7. Install the new power supply： Line up the holes on the new power supply with mounting holes on the rear of the chassis and secure it to the chassis with the four screws.

  • Page 46: Replacing The Card Reader Module

    Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Remove the front bezel. Refer to “Removing the front bezel”. Lenovo Erazer X510Hardware Maintenance Manual...
  • Page 47 Step 6. Use a screw driver to push the pin that lock top cover to the chassis , then slide the top cover toward the rear of the computer to remove the top cover. Step 7. Press the pins that lock the top USB-audio-card reader module , then press it down to remove Chapter 8 Replacing hardware...

  • Page 48: Replacing The Usb-Audio Module

    Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Lenovo Erazer X510Hardware Maintenance Manual...
  • Page 49 Step 5. Remove the front bezel. Refer to “Removing the front bezel”. Step 6. Use a screw driver to push the pin that lock top cover to the chassis , then slide the top cover toward the rear of the computer to remove the top cover. Step 7.

  • Page 50: Replacing The Front I/O Board

    Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Use a screw driver to push the pin that lock top cover to the chassis , then slide the top cover toward the rear of the computer to remove the top cover. Lenovo Erazer X510Hardware Maintenance Manual...
  • Page 51 Step 6. Disconnect the power cable from the power board. Chapter 8 Replacing hardware...
  • Page 52 Step 10. Install the new power board: Line up the new power board with the bracket, then secure the power board with the two pins. Connect the power board cable to the connector on the power board. Reattach the top cover. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 53: Replacing The Motherboard

    Step 11. Reattach the computer cover. Replacing the motherboard Note: For this procedure, it helps to lay the computer flat. To replace the motherboard: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.
  • Page 54 Reattach the Wi-Fi card, CPU, heat-sink assembly, graphic card, memory module to the new motherboard. Connect the all cables to the new motherboard. Reattach the graphic card. Step 14. Reattach the computer cover. Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 55: Chapter 9. Fru Lists

    HMT41GU6AFR8C-PB 8GB D3-1600 MEMORY 1100647 MT16JTF1G64AZ-1G6E1 8GB D3-1600 MEMORY 1100669 Elp_R J4208EBBG-GN-F 8GB D3L-1600 MEMORY 1100648 Graphics MSI@Geforce GTX 650@2G/B/2D/mHDMI VGA 11201703 11201867 MSI@Geforce GTX 660@1.5G/B1/2D/DP/H VGA AMD@HD8950@3G/B/D/H/2miniDP VGA 11201704 11201702 Bitland@HD8670@2G/B/DB/H/D VGA Bitland@Geforce GTX 760@2G/A/2D/DP/H VGA 11202298 © Copyright Lenovo 2013, 2013...
  • Page 56 LX(ASAP) 1.8M C13 UL power cord LW BLK1.8m ANE Power Cord® 31026350 31026140 VL BLK1.8m ANE Power Cord® LX(ASAP) 1.8M C13 ANZ power cord 31049524 31039730 LW 1.8m JAPAN Power Cord® Volex 1.8M C13 JPN power cord 31049514 Lenovo Erazer X510Hardware Maintenance Manual...
  • Page 57 LX(ASAP) 1.8M C13 JPN power cord 31049523 31026096 LW BLK1.8m BS Power Cord® VL BLK1.8m BS Power Cord(R) 31026082 31502861 LX(ASAP) 1.8M C13 UK power cord LW BLK1.8m VDE Power Cord® 31026355 31026144 VL BLK1.8m VDE Power Cord® LX(ASAP) 1.8M C13 EU power cord 31049522 31033216 LW BLK1.8m India power cord(R)
  • Page 58 90203455 GS 7+15 SATA cable(290+150mm) 31504682 X510 Chassis Front Panel 90203448 90203449 X510 Chassis Top Cover(w/o button) X510 ODD Bezel 90203450 90203451 X700 Hot-swappable HDD frame X510 HDD Bracket 90203452 X510 GFX Bracket clamp 90203453 Lenovo Erazer X510Hardware Maintenance Manual...

  • Page 59: Chapter 10. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2013, 2013...

This manual is also suitable for:

10143/90adErazer x510 10140/90acErazer x510 10143/90ad

Table of Contents