Table of Contents
Advertisement
Quick Links
STP-102S / STP-102P
Operator's Manual
ELECTRO- MECHANICS
Warning - U.S
DATE: July. 2001
This equipment has been tested and found to comply with the limits for a Class A
MANUAL REVISION 2.0
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interface when the equipment is
operated in a commercial environment. This equipment generates uses, and can
radiate radio frequency energy and, if not installed and uses in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Notice - Canada
This Apparatus complies with class "A" limits for radio interference as specified in
the Canadian department of communications radio interference regulations.
Introduction
The STP-102S and STP-102P Roll Printer is designed for use with electric instruments
such as system ECR, POS, banking equipment peripheral equipment, etc.
The main features of the printer are as follows:
Please be sure to read the instruction in this manual carefully before using your
new STP-102S and STP-102P.
TEL : 82-31-210-5620
FAX : 82-31-210-5589
1. High speed printing
2. Low noise thermal printing.
3. RS-232 serial interface (STP-102S). Parallel interface (STP-102P).
4. The data buffer allows the unit to receive print data even during printing.
5. Different print densities can be selected by DIP switches.
NOTE
The socket-outlet shall be near the equipment and it shall be easy
accessible.
Advertisement
Table of Contents
Related Manuals for Samsung STP-102P
Summary of Contents for Samsung STP-102P
- Page 1 Canadian department of communications radio interference regulations. Introduction The STP-102S and STP-102P Roll Printer is designed for use with electric instruments such as system ECR, POS, banking equipment peripheral equipment, etc. The main features of the printer are as follows: 1.
-
Page 2: Table Of Contents
Avoid or storing the printer in the place subject to excessive moisture. - Serial Type (STP-102S) Do not use or store, horizontal surface for the printer. Avoid places subject to - Parallel Type (STP-102P) intense vibration or shock. APPENDIX B - Specification... -
Page 3: Printer Part Names
POWER(green) The POWER light is on when the printer power is on. ERROR(red) STP-102S STP-102P 1) The error LED blinks fast when paper is out. 2) The error LED blinks when the Near End Sensor triggered. Control Panel POWER ERROR... -
Page 4: Chapter 2. Connecting The Cable
3. Plug the power supply's DC cable connector into the printer's power connector as shown below. 25 Pin Male Type STP-102S / STP-102P 3. Plug the other end of the cable into the computer 4. Plug the AC adapter's power cord into an electrical outlet. -
Page 5: Chapter 3. Installing The Paper Roll
Chapter 3. Installing the Paper Roll 2-2. Connecting the printer to your Computer Use a paper roll that matches the specifications. STP-102P You need an appropriate serial interface cable to connect your computer to the NOTE printer's built-in interface. The printer must be turned off before installing the paper roll. -
Page 6: Chapter 4. Setting The Dip Switching
Chapter 4. Setting the DIP Switches DIP switch functions CAUTION Turn off the printer while setting the DIP switch to prevent an electrical short, which can Dip Switch damage the printer. Level D/W1 D/W2 S/W3 2400 4800 You can change your interface and printer density settings by changing the DIP switch 9600 setting. -
Page 7: Chapter 5. Running The Self Test
After a number of lines are printed, the printer indicates the end of the self-test by printing " ** TEST COMPLETED ** ". If the self-test is completed, then you must reboot your printer. Followings are the self-test results with STP-102S and STP-102P. - Page 8 PC860 : Portuguese PC850 : Multilingual...
- Page 9 PC863 : Canadian - French PC865 : Nordic...
- Page 10 Space Page...
-
Page 11: Chapter 7. Functions
Chapter 7. Functions The commands listed in the table below are available for control of the printer. Commands Command Classification Command Classification Standard Standard Command Name Command Name Mode Mode Executing Setting Executing Setting Horizontal tab ESC \ Set relative print position Print and line feed ESC a Select justification... -
Page 12: Chapter 8. Control Commands
Chapter 8. Control Commands ESC SP n [Name] Set right-side character spacing. [Format] ASCII Decimal 0 < n < 255 [Range] [Description] Sets the character spacing for the right side of the character to n dots. Command Notation [Name] The name of the command. [Format] the code sequence. - Page 13 ESC 3 n m nL nH d1...dk [Name] Set line spacing. [Name] Select bit-image mode. [Format] ASCII [Format] ASCII m nL nH d1 ... dk m nL nH d1 ... dk Decimal Decimal m nL nH d1 ... dk 0 < n < 255 [Range] [Range] m = 0, 1, 32, 33...
- Page 14 ESC J n ESC \ nL nH [Name] Set relative print position. [Name] Print and feed paper. [Format] ASCII 1n, nH [Format] ASCII 1n, nH Decimal 1n, nH Decimal 0 < nL < 255 0 < n < 255 [Range] [Range] 0 <...
- Page 15 ESC c 5 n GS ! n [Name] Enable/Disable panel buttons. [Name] Select character size. [Format] ASCII [Format] ASCII Decimal Decimal 0 < n < 255 0 < n < 255 [Range] [Range] (1 < vertical number of times < 8, 1 < horizontal number of times < 8) [Description] Enables or disables the panel buttons.
- Page 16 GS W nL nH GS B n [Name] Set printing area width. [Name] Turn white/black reverse printing mode on/off. [Format] ASCII [Format] ASCII Decimal Decimal 0 < nL < 255 0 < n < 255 [Range] [Range] 0 < nH < 255 [Description] Turn on or off white/black reverse printing mode.
-
Page 17: Appendix A: Connectors
0 < m < 6 (k and d depends on the bar code system used.) [Range] 65 < m < 73 (n and d depends on the bar code system used) PARALLEL INTERFACE CONNECTOR (STP-102P) [Description] Selects a bar code system and prints the bar-code. - Page 18 APPENDIX B: Specification Printing method Thermal line printing Dot density 200 x 200 Dpi (8 dot/mm) Printing width 48mm Paper width 58mm Characters per line 42 (Font A)(12x24) ,56(Font B)(9x24) Approximately 1.97 inchs/sec Printing speed 50 mm/sec at 25°C/printing duty 12.5% Receive buffer size 15K bytes 7.5V...