Hoshizaki F-500BAF Instruction Manual
  1. Manuals
  2. Brands
  3. Hoshizaki Manuals
  4. Ice Maker
  5. F-500BAF
  6. Instruction manual
Hoshizaki F-500BAF Instruction Manual

Hoshizaki F-500BAF Instruction Manual

Self-contained flaker
Hide thumbs Also See for F-500BAF:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
Hoshizaki
Hoshizaki America, Inc.
"A Superior Degree
of Reliability"
www.hoshizaki.com
Self-Contained Flaker
Model
F-500BAF
INSTRUCTION MANUAL
Issued: 4-13-1998
Revised: 3-22-2010

Advertisement

Table of Contents
loading

Related Manuals for Hoshizaki F-500BAF

Summary of Contents for Hoshizaki F-500BAF

  • Page 1 Hoshizaki Hoshizaki America, Inc. Self-Contained Flaker Model F-500BAF INSTRUCTION MANUAL “A Superior Degree of Reliability” www.hoshizaki.com Issued: 4-13-1998 Revised: 3-22-2010...
  • Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write, or send an e-mail message to the Hoshizaki Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.

  • Page 3: Table Of Contents

    IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that may be necessary.

  • Page 4: Important Safety Information

    Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit.

  • Page 5: Specifications

    I. Specifications A. Nameplate Rating 1. F-500BAF(-C) (air-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER F-500BAF SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 COMPRESSOR 120V 7.5RLA 54.5LRA GEAR MOTOR 115V 2.4FLA 1/4HP FAN MOTOR 115V 0.85FLA 1/15HP OTHER 120V 0.08A MAXIMUM FUSE SIZE 20 AMPS MAX.

  • Page 6: Dimensions/Connections

    B. Dimensions/Connections 1. F-500BAF(-C) (air-cooled)

  • Page 7: Installation And Operating Instructions

    II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with all applicable national, state, and local regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin.

  • Page 8: How To Remove Panels

    B. How to Remove Panels See Fig. 1 • Top Panel: Remove the screws and lift off. • Front Panel: Remove the screws and lift up and towards you. • Left Side Panel: Remove the screws and lift off. • Sliding Door: Remove the top panel and front panel, then slide the sliding door to the left. Top Panel Sliding Door Left Side Panel Control Box Cover Front Panel Air Louver Air Filter Fig. 1...

  • Page 9: Location

    C. Location CAUTION 1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within 45°F to 100°F (7°C to 38°C); Normal operating water temperature should be within 45°F to 90°F (7°C to 32°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect icemaker performance.

  • Page 10: Electrical Connection

    E. Electrical Connection WARNING 1. Electrical connection must be hard-wired and must meet national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric shock, serious injury, fire, or severe damage to equipment. 2.

  • Page 11: Water Supply And Drain Connections

    10 PSIG. Do not run the icemaker until the proper water pressure is reached. • A plumbing permit and services of a licensed plumber may be required in some areas. • External filters, strainers, or softeners may be required depending on water quality. Contact your local Hoshizaki distributor for recommendations. • Water supply pressure should be a minimum of 10 PSIG and a maximum of 113 PSIG. If the pressure exceeds 113 PSIG, the use of a pressure reducing valve is required. • Icemaker water supply inlet is 1/2" female pipe thread (FPT). A minimum of 3/8" OD copper tubing is recommended for the icemaker water supply line.
  • Page 12 Drain Outlet 3/4" FPT Bin Drain Outlet 3/4" FPT Two-inch (5 cm) air Fig. 3 F-500BAF Floor Drain Separate piping to approved drain. Leave a two-inch (5 cm) vertical air gap between the end of each pipe and the drain.

  • Page 13: Final Checklist

    G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F (7°C to 38°C) and the water temperature within 45°F to 90°F (7°C to 32°C) all year around? 3) Is there at least 6"...

  • Page 14: Startup

    H. Startup WARNING 1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. 2. If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3.

  • Page 15: Cleaning And Maintenance

    Make sure that none have fallen into the storage bin. A. Cleaning and Sanitizing Instructions Hoshizaki recommends cleaning and sanitizing this unit at least twice a year. More frequent cleaning and sanitizing, however, may be required in some existing water conditions.

  • Page 16: Cleaning Solution

    For safety and maximum effectiveness, use the solution immediately after dilution. Dilute 4.8 fl. oz. (142 ml) of Hoshizaki "Scale Away" with 0.8 gal. (3 l) of warm water. This is a minimum amount. Make more solution if necessary. 2. Cleaning Procedure 1) Turn off the power supply, then remove the top and front panels.

  • Page 17: Sanitizing Solution

    13) Turn on the power supply and allow the water system to drain for 5 minutes. 14) Turn off the power supply, then remove the top and front panels. Move the flush switch to the "ICE" position, then replace the panels in their correct positions. 15) Open the icemaker water supply line shut-off valve, then turn on the power supply to supply water to the reservoir.

  • Page 18: Sanitizing Procedure - Final

    10) Turn off the power supply, then remove the top and front panels. Move the flush switch to the "FLUSH" position, then replace the panels in their correct positions. 11) Turn on the power supply and allow the water system to drain for 5 minutes. 12) Turn off the power supply.

  • Page 19: Maintenance

    Consult with your local distributor about inspection and maintenance service. To obtain the name and phone number of your local distributor, visit www.hoshizaki.com or call Hoshizaki Technical Support at 1-800-233-1940 in the USA. WARNING 1.

  • Page 20: Preparing The Icemaker For Long Storage

    Maintenance Schedule (continued) Frequency Area Task After Upper Bearing Inspect. Replace both upper bearing and lower bearing if wear exceeds 3 Years, (extruding head); factory recommendations. Replace the mechanical seal if the seal's contact then Yearly Lower Bearing surfaces are worn, cracked, or scratched. and O-Ring (lower housing);...
  • Page 21 6) Turn on the power supply, then move the power switch to the "ON" position. Blow out the evaporator drain line using the compressed air or carbon dioxide supply until water stops coming out. 7) Move the power switch to the "OFF" position, then turn off the power supply. Reconnect the evaporator drain line hose.
  • Page 22 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A2HA10E...

Table of Contents