Tilling Tips& Techniques - Troy-Bilt Pony 12211 Owner's Manual

Tilling Tips& Techniques
Let the tiller do the work
• While tilling, relax and let the wheels
pull the tiller along while the tines do
the digging. Walk on the side that is
not yet finished (to avoid making foot-
prints in the freshly tilled soil) and
lightly, but securely grip the handlebar
with just one hand.
• Avoid pushing down on the handlebars
in an attempt to force the tiller to dig
deeper. Doing so takes the weight off
the powered wheels, causing them to
lose traction. Without the wheels
helping to hold the tiller back, the tines
will attempt to propel the tiller - often
causing the tiller to skip rapidly across
the ground. (Sometimes, slight down-
ward pressure on the handlebarswill
help get through a particularly tough
section of sod or unbroken ground, but
in most casesthis won't be necessary
at all.)
Tilling depths
• Avoid trying to dig too deeplytoo
quickly, especially when busting sod or
when tilling soil that hasn't been tilled
for some time. Use shallow depth reg-
ulator settings (only an inch or two
deep) for the first passesthrough the
garden area. With each succeeding
pass, adjust the depth regulator to dig
another inch or two deeper. (Watering
the garden area a few days prior to
tilling will make tilling easier, as will
letting the newly worked soil set for a
day or two before making a final, deep
tilling pass.)
• When cultivating (breakingup the
surfacesoil around plants to help
destroy weeds), use very shallow depth
settingsto prevent injury to plantswhose
roots often grow close to the surface. If
needed,lift up on the handlebarsslightly
to preventthe tines from digging too
deeply. (Cultivatingon a regular basis
not only eliminatesweeds,it also loosens
and aeratesthe soil for better moisture
absorption and faster plantgrowth.)
Avoidtilling soggy, wet soil
Tilling wet soil often results in large,
hard clumps of soil that can interfere
with planting. If time permits, wait a day
or two after heavy rains to allow the soil
to dry before tilling. Test soil by squeez-
ing it into a ball. If it compresses too
easily, it is too wet to till.
Avoid making footprints
When possible,walk on the untilled side
of the unit to avoid making footprints in
the freshly tilled soil. Footprints cause
soil compaction that can hamper root
penetration and contribute to soil
erosion. They can also "plant" unwanted
weed seeds back into the freshly tilled
ground.
Choosingcorrectwheel
and tine speeds
With experience,you will find the 'Just
right" tilling depth and tilling speed com-
bination that is best for your garden.
Set the EngineThrottle Control Lever to
a speedto give the engine adequate
power and yet allow it to operate at the
slowest possible speed...at least until
you have achieved the maximum tilling
depth you desire. Fasterengine speeds
may be desirable when making final
passes through the seedbedor when
cultivating. Selection of the correct
engine speed, in relation to the tilling
depth, will ensure a sufficient power
level to do thejob without causing the
engine to labor.
Suggested tilling patterns
• When preparing a seedbed,go over the
same path twice in the first row, then
overlap one-half the tiller width on the
rest of the passes (see Figure 4-6).
When finished in one direction, make a
second pass at a right angle as shown
in Figure 4-7. Overlap each pass for
best results (in very hard ground it may
take three or four passesto thoroughly
pulverize the soil).
• If the garden size will not permit
lengthwise and then crosswise tilling,
then overlap the first passesby one-
half a tiller width, followed by succes-
sive passesat one-quarter width (see
Figure 4-8).
• With planning, you can allow enough
room between rows to cultivate (see
Figure 4-9). Leaveroom for the hood
width, plus enough extra room for
future plant growth.
Figure 4.6
F
Figure4.7
Figure 4.8
Figure 4.9