Scag Power Equipment SWZU Operator's Manual page 23

Ref. Part
No. No. Description
1 461173 Cutter Deck With Decals
2 04017-27 Capscrew, 3/8-16 x 1.0" Serrated Flange
3 04021-05 Lock Nut, 3/8-16 Center Lock
4 48100-15 Bushing, 376 ID Oilite
5 481632 Wheel, Anti-Scalp
6 422478 Bracket, Anti-Scalp Wheel
7 04003-26 Bolt, Carriage 3/8-16 x 4.0"
8 04021-09 Hex Nut, 3/8-16 Elastic Stop
9 04043-04 Flatwasher, 3/8 (.938 x .391 x .105)
10 48224 Ball Bearings
11 461175 Idler Arm RH
12 43503 Pivot, Idle - Short
13 04003-04 Bolt, Carriage 5/16-18 x 1.0"
14 422713 Base, Idler Pivot
15 04001-31 Capscrew, Hex Head 3/8-16 x 2.50"
16 04001-45 Capscrew, Hex Head 3/8-16 x 2.0"
17 04001-136 Capscrew, Hex Head 3/8-16 x 1.50"
18 04019-04 Nut, 3/8-16 Serrated Flange
19 48181 Pulley, Idler
20 481838 Pin Assembly (Incl. 21 & 23)
21 04020-25 Nut, 3/8-24 Jam
22 43512 Spacer, Deck Adjustment Pin
23 481539 Rod End, Male 3/8-24
24 46631 Spindle Assembly
25 43309 Spacer, Spindle
26 04001-41 Bolt,Hex Head 5/8-11 x 9.50"
27 04040-10 Flatwasher, 5/8 W
28 48110 Cutter Blade 16-1/2"
28A 48184 Cutter Blade 16-1/2" Hi Lift
29 04001-10 Bolt, Hex Head 5/16-18 x 1.25"
30 43298 Spindle Shaft
31 481024 Seal, Cutter Spindle - Top
32 481022 Tapered Bearings (Two)
33 48114-04 Grease Fitting
34 43294 Spindle Housing
* Common hardware which should be purchased locally. All bolts are Grade 5 plated, all other fasteners zinc plated.
48" CUTTER DECKS
35 48677
36 43312
37 43296
38 481025
39 43297
40 481035
41 481625-01 Wing Nut, 3/8-16
42 451118
43 04001-09
44 04060-08
45 43515
46 48926
47 48038
48 48924
49 48923
50 481881
51 04015-14
52 04020-09
53 48087
54 422745
55 04001-62
56 461174
57 04001-51
58 461054
59 04019-03
60 481597
61 04001-08
62 481050
63 04021-09
64 04019-03
65 04001-31
66 04063-08
67 48550
68 43510
69 422744
70 04110-03
19
Relief Fitting, Cutter Spindle
Spacer Outside
Spacer, Inside
Seal, Cutter Spindle - Bottom
Spindle Bushing
Nut, Spindle
Roller Shaft
Bolt, Hex Head 5/16-18 x 1.0"
Pin, Slotted Spring 3/16 x 1.50"
Pin, Deck Adjustment Rear
Tapered Hub
Guide, Roller
Pulley
Pulley, 5.75 Double Grove
Belt, Deck Drive
Capscrew, Socket Head 1/4-20 x 1.375"
Hex Nut, 5/8-11
Belt, Cutter Deck
Belt Cover, RH
Capscrew, Hex Head 3/8-16 x 3.25"
Idler Arm Weldment
Capscrew, Hex Head 3/8-16 x 3.75"
Discharge Chute
Nut, 5/16-18 Serrated Flange
Spring, Deck Idler
Bolt, Hex Head 5/16-18 x 4.25"
Spring, Chute Return
Nut, 3/8-16 Elastic Stop
Nut, 5/16-18 Serrated Flange
Bolt, Hex Head 3/8-16 x 2.50"
Key, 1/4 x 1/4 x 2.0"
Pulley, Idler
Pivot, Idler - Long
Belt Cover LH
U-Nut, 3/8-16