Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
M10 Monitor/ Dual-Zone Controller
BEFORE YOU START THE INSTALLATION, READ THIS GUIDE!
Below is an outline of the installation process, showing the installation sequence we recom-
mend, and the pages that describe each step.
Contents - Steps to a successful installation:
Step One:
Step Two:
Step Three:
Step Four:
Step Five:
Step Six:
Step Seven
Frequently Asked Questions
M10 Diagnostics
Dual Zone and Multi-screen Installations
System Diagram
NOTICE OF INTENDED INSTALLATION AND USE
ROSEN ENTERTAINMENT SYSTEMS OVERHEAD VIDEO PRODUCTS ARE NOT INTENDED FOR
VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY TO BE VIEWED BY REAR-SEAT
OCCUPANTS. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH
SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH,
AND COULD ALSO VIOLATE STATE LAW. ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY
LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY
IMPROPER OR UNINTENDED INSTALLATION AND/OR USE.
Rosen M10 Installation Guide
Installation Guide
Make sure you have all the components and tools you'll need
Check out the vehicle and plan your work -
console location, harness routing, etc.
Cut the headliner and mount the Bracket
Route the harnesses and make all wiring connections
Connecting the Domelight wires
Install the main unit
Test the system, reassemble the vehicle, re-test quickly
M10 Configuration and Programming
A10 Installation Manual Revision A(090804) RES PN 9100395-91 Rev B
Copyright 2004 Rosen Entertainment Systems
866-Go Rosen
www.rosenentertainment.com
2
3
4-9
10
11
12
13
14-16
17
18
19
20
1
Advertisement
Table of Contents
Related Manuals for Rosen M10 Monitor/ Dual-Zone Controller
Summary of Contents for Rosen M10 Monitor/ Dual-Zone Controller
-
Page 1: Installation Guide
OCCUPANTS. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO VIOLATE STATE LAW. ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE. - Page 2 R5001 10-disc DVD Changer (also requires kit w/ AC3024 harness and adapter) Rosen AC3072 Dual-Channel Wireless Headphones (for dual-zone applications) Rosen external game plate/ harness AC3077 Rosen 43mm Tall Trim Ring (CV2033 G and N), 60mm Tall Trim Ring (CV2034N), or Toyota Sienna Trim Ring (CV2035N) Rosen M10 Installation Guide...
-
Page 3: Check The Battery
OCCUPANTS. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO VIOLATE STATE LAW. ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE. -
Page 4: Front Of Vehicle
Vehicle Roof Roof Beam Cables Headliner Trim Ring Bracket oriented laterally Front of Vehicle Threaded standoffs Passenger for Mounting Screws side mounting holes SOURCE ENTER OPEN Driver’s side Threaded standoffs Connectors mounting holes for Mounting Screws (Continued) Rosen M10 Installation Guide... - Page 5 Trim Ring Optional Spacers (included in Front of Vehicle Bracket oriented laterally hardware kit) Threaded standoffs Passenger for Mounting Screws side mounting holes SOURCE ENTER OPEN Driver’s side Threaded standoffs Connectors mounting holes for Mounting Screws Rosen M10 Installation Guide...
- Page 6 Strike firmly with ball-peen hammer Bend/break lines Bend/ Sturdy workbench break lines Rosen M10 Installation Guide...
- Page 7 Note: If you plan on removing unused standoffs from the bracket, you can reduce the number of holes to cut - see page 8. 5 Test-fit the mounting bracket into the headliner opening from above. Rosen M10 Installation Guide...
-
Page 8: Step 3: Mount The Bracket
Strike firmly with ball-peen hammer Bend/break lines Bend/ Sturdy workbench break lines Rosen M10 Installation Guide... - Page 9 Mounting Screws Long-axis Bracket Positioning Threaded Threaded standoffs standoffs Mounting Mounting Screws Screws Threaded Threaded standoffs standoffs Connectors Bend or break Bracket at this point Front of Vehicle to create a cable exit! (See Pages 5, 7) Rosen M10 Installation Guide...
-
Page 10: Installation Precautions
12V(+) Switched Accessory (Fused 1 A) Black Chassis (-) Ground Orange Vehicle Illumination Input (12V(+) when the parking lights are on) IMPORTANT: - Connecting the Red wire to constant 12V(+) causes battery drain and premature battery failure. Rosen M10 Installation Guide... - Page 11 12V Constant circuit in the vehicle. Note: The domelight has a built-in five-minute limit timer . This is to prevent accidental battery drain. To turn the domelight back on, press the domelight button again. Rosen M10 Installation Guide...
-
Page 12: Install The Main Unit
– if there is any binding, check for uneven screw torquing. Binding indicates that the side edges of the trim ring need to be trimmed to relieve pressure on the sides of the M10. Note: Do not re-assemble the vehicle yet! Rosen M10 Installation Guide... - Page 13 88.1, 88.3, 88.5, 88.7, 88.9 106.7, 106.9, 107.1, 107.3, 107.5, 107.7, 107.9, Off. 5 If you are using a Rosen M10-compatible source, you will have to use the Install Setup Menu on Page 14 to select the proper source unit. If you are installing this M10 as a “slave”...
- Page 14 Input Label Selection: DVD Changer, TV Tuner, Satellite, External Game, Aux Input 2. DVD Region: Allows authorized change to the DVD Region setting. FMM OSD. This changes the OSD’s to match an optional External Rosen FMM. Output B on/off. This disables the Output B button on the remote.
- Page 15 There are two cases where you may want to turn off one of both IR channels of the M10. When the M10 is a slave screen to a Rosen unit with Dual-Zone control and IR transmit- ters (such as the A10), you may want to turn off both IR channels to prevent IR intererence.
- Page 16 A. If a second screen is added, it will show the same image as the main screen. To restore all Install Setup settings to their original factory defaults 1) Enter the Install Setup screen: Scroll down to RESTORE DEFAULTS 2) Use the RIGHT button to reset the settings to factory defaults. Rosen M10 Installation Guide...
-
Page 17: Frequently Asked Questions
Check power and ground connections. This is a symptom of poor electrical connections. Make sure you are not using a damaged DVD disc. Call Rosen Technical Support to determine if any of the internal protection modes are being triggered - (888) 883-2790. - Page 18 After 2 minutes, or if the ignition is turned off, this screen will disappear, but the events will still be retained in memory if you did not press ENTER. Rosen M10 Installation Guide...
- Page 19 (For the ability to select between the two sources for audio, the optional AC3007 Dual-Channel Wireless Headphones are re- quired.) Rosen recommends connecting only wide-screen displays to the M10. Sample System Diagram with two “headrest” monitors...
- Page 20 Rosen M10 System Wiring Diagram * Wiring Connections, AC3024 Magenta Input Harness Note: RCA connections: Black cables are required, Right Audio In Gray cables are optional. White Left Audio In (The Green cable is Yellow Video In included, but not required)